ADEMCO VISTA 10 Instrukcja Konfiguracji Pobierz pdf (Strona 61)

11-1

SECTION 11

Testing the System

•••••••••••••••••••••••••••••••••••••••••••••••••

Local Tests

After the security system installation is complete, test the system as follows:

1. With the system in the disarmed state, check that all zones are intact. If a

NOT

READY

message

is displayed, press the [

✱

] key to

display the faulted zone(s). Restore faulted zone(s) if necessary, so that the

READY

message

is displayed.

2. Enter the security code and press the TEST [5]

key.

The external sounder will sound for 1 second. If the backup battery is discharged or missing, the sounder may not turn on and a

LOW BATTERY report will be transmitted with a TEST report.

Note that the keypad will beep once every 40 seconds as a reminder that the system is in the Test mode.

3. Fault and restore every sensor individually to assure that it is being monitored by the system. Each time a protection zone is

faulted, the keypad will sound 3 beeps, and the identification of each faulted protection zone should appear on the keypad display.

NOTE:

For 5800 wireless systems, triggering a zone set to Arm-AWAY, Arm-STAY, or Disarm will take the system out of the

TEST mode and cause that action.

4. Walk in front of any interior motion detectors (if used) and listen for the required sound as movement is detected. The

identification of the detector should appear on the display when it is activated.

NOTE:

Wireless motion detectors (passive infrared units) will send signals out only if they have been inactive for 3 minutes.

5. Follow the manufacturer's instructions to test all smoke detectors, to ensure that all are functioning properly. The identification of

each detector should appear on the display when each is activated.

6. Turn off the test mode by entering the security code and pressing the OFF [1] key.

Communication Tests

Alarm messages will be sent to the central station during the following tests. Notify CS personnel

in advance

that

tests will be in progress.

1. Arm the system (STAY) and fault one or more perimeter zones. After 15 seconds, silence alarm sounder(s) by entering the security

code and pressing the OFF [1] key.

Arm the system AWAY, and check the Entry/Exit zones for the programmed exit and entry delays.

2. Check the keypad-initiated alarms that are in the system by using the Panic keys (or key pairs on some keypads). If a key (or key

pair) has been programmed for audible emergency, the keypad will emit a steady alarm sound, and

ALARM

and zone number will

be displayed.

If a key (or key pair) has been programmed for silent emergency, there will be no audible alarms or displays, but a report will be

sent to the central station.

If a key (or key pair) has been programmed for fire, the keypad and external sounder will emit an interrupted alarm sound, and

ALARM, FIRE

and

zone number

will be displayed.

Silence alarms by entering the security code and pressing the OFF [1] key.

3. If Output Relay Units have been installed, test their programmed action.

4. Notify the central station when all tests are finished, and verify results with them.

To test the wireless part of the system and the RF Receiver, perform the two following tests:

Transmitter Sniffer Mode

and

Go/NoGo Test Mode.

Transmitter Sniffer Mode

Make sure the system is

disarmed

before trying to enter this mode.

1. Key

Installer Code

[#]

[3]

This

initiates a procedure that checks that all 5800 Series transmitters have been properly

programmed.

NOTE:

If the communicator is in the process of sending a report to the central station, the system will not go into the Sniffer mode. If

so, wait a few minutes, and try again.

The keypad displays all zone numbers of wireless units programmed into the system. As the system receives a signal from each of the

transmitters, the zone number of that transmitter disappears from the display. The transmitter codes may be checked upon

installation, or in an installed system.

All the wireless zone numbers should disappear after about 1-1/2 hours.

NOTE:

Any transmitter that is not properly entered into the system will not turn off its zone number.

2. Exit the Transmitter Sniffer mode by keying

Installer code + OFF [1]

key.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 79 80

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO VISTA 10 Instrukcja Konfiguracji Strona 61

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA 10