ADEMCO VISTA 10 Instrukcja Konfiguracji Pobierz pdf (Strona 37)

Section 5 - Zone Programming

5–3

PROMPT VALID ENTRIES EXPLANATION

10 INPUT S/N L

A022-4064 ?

Loop Number Entry

[

✱

]

to accept and continue

NOTE:

If you use the [C] key to copy the previously enrolled serial

number, the cursor moves to the Loop column (L) with the serial

number displayed, and displays a question mark ‘

” for the loop

number.

Enter the loop number and press [

✱

]. Refer to the graphic of

wireless devices on a following page in this section for the correct

number of loops and loop identification numbers.

The system then checks for a duplicate serial/loop number

combination.

If a

duplicate

serial/loop number combination is found, the keypad

emits a single long beep, and displays the serial number along with

a “

” for the loop number, allowing you to reenter the correct loop

number.

XMIT

CONFIRM

PRESS

✱

TO SKIP

Confirmation Option

[

✱

]

to continue

This prompt appears only if you answered

Yes

to the first prompt in

this section.

The system enters a confirmation mode so that the operation of the

actual programmed input can be confirmed. Activate the loop input

or button that corresponds to this zone.

We recommend that you confirm the programming of every

transmitter before proceeding to the next zone.

Keyd A022-4063

Rcvd A022-4064 1

No Match

If the serial/loop number combination transmitted

does not match

the serial number entered, a display similar to the one at left

appears. If the loop number does not match, it is also displayed.

If so, activate the transmitter's loop input or button one or more

times. If a match is still not obtained (i.e., summary display does

not appear), press the [#] key twice and enter the correct loop

input or, if correct, press the [#] key again and then enter the

correct serial number.

Zn ZT – RC In: L

10 03 – 10 RF:

Summary Display

[

✱

]

to accept zone summary

and continue

If the

serial number transmitted matches

the serial number

entered, the keypad beeps 3 times and a summary display appears,

showing that zone's programming. Note that an “s” after the loop

number indicates that a transmitter’s serial number has been

enrolled.

PROGRAM ALPHA?

0 = NO 1 = YES 0

Alpha Descriptors

0 = no

1 = yes

[

✱

]

to continue

If you want to program descriptors for zones now, enter

(Yes) and

refer to

SECTION 8: Alpha Descriptor Programming

for

available descriptors.

ENTER ZN NUM.

(00 = QUIT) 11

Next Zone Number

00 = quit

If you entered

(No) above, the system returns you to the

ENTER ZN NUM.

prompt for the next zone.

When all zones have been programmed, enter

to quit

NOTE:

Following the successful enrollment of each wireless device, remove

ONE

of the serial number labels from the

device and affix it in the appropriate column on the ENROLLED TRANSMITTERS worksheet of the Programming

Form. Then enter the other information (zone number, zone type, loop number, etc.) relevant to that device. This

information will be useful if any troubleshooting is needed later on. The installer may want to consider leaving this

worksheet at the site (in the panel cabinet).

Testing the Zones

When you have finished programming all zones, test each zone using the system’s TEST mode.

Do not use the

Transmitter ID Sniffer Mode for checking wireless transmitting devices

, as it will only check for transmission of

one zone on a particular transmitter, NOT the zones assigned to each additional loop.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 79 80

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO VISTA 10 Instrukcja Konfiguracji Strona 37

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA 10