.
ForLowRamyRaalorat
Message: 0135 5355 5555 6
J. 8E8COAIRIDIONICS REFORTINQ FORMATS
Like the Ademco Low Speed format. each alarm/lrouble/atatus message
reported in SESCOA. Radio&s. Radionlcs “Superfast” and Radionics
“BFSK” formats contains a code digit which is PROM assigned to that
message. Any digit from the full hexadecimal code set (0-9. B-F) can be
used for each of these formats for trouble/status messages (only l-6 for
alarm messages).
NOTE: The full hexadecimal code set can also be used with the
Ademco low speed format provided that the central station
receiver used can decode and display the resulting
messages. The Ademco No. 660/673 receiver can only
accommodate the code set t-9.
The Radionics central station receiver can be flagged to print the word
“Fire” when it receives an alan report, in “BFSK” format, it zone four is
designated as a tire zone. Fire zone designation for “BFSK” alarm reporting
purposes is made in the communicator PROM.
It should be tufther noted that the following reporting code assignments are
required tar the Radionics, Radionics “Superfast” and Radionics “BFSK”
tom&s in order to attain the appropriate English language printout and
diiy at the Radionics No. 6000 receiver. They apply as well to the
Ademco Low Speed. Radionics, Radionics “Superfast” and Radionics
“BASK”
tormats
for Engtish language printout at the Ademco No. 665
Receiver.
:
= Open
=ClOM
D =
Cancel (if Openings/Closings are not
mwammed)
E = Restore
F = Trouble
BFSK tormat also requires that extended data reporting be selected in the
communicator PROM and that new low battery format be selected in the
control PROM.
IV. INSTALLER PROM PROGtiMlNG
The ayatem employa two PROM integrated circuits for salec6on of
system optics. one primarily for control characteristics and one totally
for comrnt&ator characteristics Thaae PROMS are ordered aapa-
rately. Ademco No. 691 if blank and will be programmed by the installer
ff No. 691 p3 (amtml) and No. 691 P12 (communicator) it the pro-
gramming is done by Ademco to customer order. In either case the
followingfeaturechartsneedtobecunpletedasarecordofme
ayatemcorlnlulation.
CUSTOMER NAME
‘CUST. NO.
NO= Program the numbeis that you write into the boxes except for
double boxes where you program the number preprinted in a
box~nexttomeboxyoucheck.
ACONTROLPRON
camtd?Rwopsl0mup1
TO program, set Phone No. Selector Switch to “Secondary” and Rotary
Switch to Position 2 (Main Phone No.) on No. 690 PROM Programmer.
l--v-w’(l)
(SemO-9)Ij XlSsecs=-
2 Exn w
(2)
(SelectO-9)0X15secs= -
3.Exlul#Alamt
--
(select0-9)D XlSsecs=-
--o-Y
‘- t+izf?- ‘(3)
(seeto-9) 0 X4mins= -
5. AC Foww Fait
RmacIton D&y
(select 0-9) 0 X 4 mins = -
NOTES: Per U.L. Standard 1023 for a listed U.L. household burglary
installation:
‘(1) A mulmunr of 45 seconds is allowed.
72) A muhum ot 60 seconds
is
allowed.
l
(3) A mMmum
of 4 minutes is allowed.
6. &kd ZOIUS wtth Enlry/Erlt m Check 0~
Numbar
of Box
Chl?Ckd
Znl=rI fnZ=rj Znsl,2=[311
Zns 1.2.3= T-i;T1 None=~l
a
7.
Sekt F-1 Rospwmo (15 mot) Zones Check Ona
Znt -111) Zn3=~~Zns2.3-~3
Zn4=17] Zns2,4=15 Zns3,4=r]
Zns2.3.4= m None-~]
cl
8. Zona 4 Typa Setactta Check One
Jt#mw Night Burglary = m Fire*‘= ITI
Day/Night Burglary= 2
m
~u*m~NiihtBurglary=~“((Fire”=~
Day/Night Burglary= 6
m
cl
“NOTE: Selection of “No Alarm Timeout” for fire is mandatory for
listed U.L. household Cre installations per U.L. Standard 965.
B.Zonaa5and6TypeSatectton:CheckOlw
Zn 5 = Silent Panic (Console Display On), Zn 6 = Burglary:
m
0
Zn 5 = Silent Panic (Con&e Display Oft), Zn 6 = Burglary:
En ,p
I
Zn 5 = Silent Panic (Console Display On),
Zn 6 = Audible Panic:
m
2
Zn 5 = Silent Panic (Console Diiptay Off),
Zn 6 = Audible Panic:
m
6
Zn 5 = Audible Panic, Zn 6 = Burglary:
m
Zn 5 = Audibte Panic, Zn 6 = Audible Panic:
&cl
10. Abm~ Soundor Optbom Check Ona
There are two burglary siren output formats from which to select it
the optional No. 4165 Siren Driver is to be used. format #l is a
rapidly alternating HI/LO sound that is similar to an electronic bell
sound. Format #2 is a sknuly alternating HI/LO sound that is similar
to the sound produced by emergency vehicles in some locales.
The confirmation 01 arming “ding” is a brief ‘h second pulse ot the
exterior alam sounder to advise the subscriber that the system has
set up successtully after he is outside the premises. Primarily for
commercial usage. thii “Ding” is produced after kissofl (by the
central station receiver) if “closing” reporting is programmed or after
the exit delay has ended il “closing” reporting is not selected.
Theaopamt~AandBdatgnatiomrWtetotheukUonofthe
atgnmlpolamyofthooulputmTe1-l.lhboutputpmmtB8ha
syatenfs ‘mnln~ *tatus” to l xtwnd oontmlhd devkas (e.g.
motion detectors. contact identification annunciator). “A” selection
yields a 0 Volt output for “Disarmed”. a Voltage output for “Armed”.
“B” selection yields a Voltage output for “Disarmed”. 0 Volt output
tar “Armed.”
A B
Burglary Siren Output 11 (Rapid Alt. HI/LO). No Contirmatton
of Arming “Ding”:
lliilzlm
Burglary Siren Output #2 (Slow AH. HI/LO). No Confirmation
of Arming “Ding”:
(16 strony)
(64 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji