ADEMCO VISTA 10 Instrukcja Konfiguracji Strona 40
- Strona / 80
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
VISTA-10SE Installation and Setup Guide
5–6
PROMPT VALID ENTRIES EXPLANATION
XMIT TO CONFIRM
PRESS
✱
TO SKIP
Confirm
[
✱
]
to continue
The prompt to confirm appears
.
This prompt will only appear if the
first prompt after entering
✱
58 was answered “Yes.” To confirm,
activate the loop input or button that corresponds to this zone.
The system checks for duplicate. If a duplicate exists, the keypad
emits a single long beep, and displays the serial number along with a
“
?
” for the loop number, allowing you to reenter the correct loop
number
Press [#] to back up and reenter the serial and/or loop number.
Keyd A022-4063 1
Rcvd A022-4064 1
If Serial or Loop
Numbers do not match
after activating the
transmitter
[
✱
]
to continue
If the serial/loop number combination transmitted
does not
match
the serial and loop number entered, a display similar to
the one at left appears. If the loop number does not match, it will
also be displayed. If so, activate the transmitter’s loop input or
button one or more times.
If a match is still not obtained (i.e., summary display does not
appear), press the [#] key twice and enter the correct loop input or,
if correct, press [#] again and then enter the correct serial number.
Zn
ZT – RC In: L
11
03
– 10 RF:
1s
Note that an “s”
indicates that a
transmitter’s serial
number has been
enrolled.
Summary Screen
[
✱
]
to continue
If the serial number transmitted matches the serial number
entered, the keypad beeps 3 times and advances to the Summary
display of the next zone to be programmed.
NOTE:
Following the successful enrollment of each wireless device, remove
ONE
of the serial number labels from the
device and affix it in the appropriate column on the ENROLLED TRANSMITTERS worksheet of the Programming
Form. Then enter the other information (zone number, zone type, loop number, etc.) relevant to that device. This
information will be useful if any troubleshooting is needed later on. You may want to consider leaving this worksheet at
the site (in the panel cabinet).
Testing the Zones
When you have finished programming all zones in
✱
58, test each zone using the system’s TEST mode.
Do not use the
Transmitter ID Sniffer Mode for checking wireless transmitting devices
, as it will only check for transmission of
one zone on a particular transmitter, NOT the zones assigned to each additional loop.
To Remove a Zone
To either temporarily or permanently remove a wireless zone from the 5800 system:
SET TO CONFIRM?
0 = NO 1 = YES 0
Set to Confirm
0 = no
1 = yes
1. Enter the programming mode:
Key
Installer Code
+
8 + 0
and press
✱
56
.
2. The prompt at left appears. Select 1 = yes.
Enter Zn Num.
(00 = Quit) 10
Zone Number
00 = quit
01-25 = zone to be
removed
[
✱
]
to continue
The prompt at left appears.
3. Enter zone number to be removed. (Example: 10 used here.)
Zn
ZT – RC In: L
10 03 – 10 RF:1s
Summary of Zone
[
✱
]
to continue
The summary prompt of selected zone appears.
- 6HFXULW\6\VWHP 1
- Table of Contents 3
- (if used) 4
- (if programmed) 4
- List of Figures 5
- Introduction 7
- SECTION 2 9
- DETAIL A 10
- DETAIL B 10
- KEYPAD CONNECTOR CABLE 11
- AUX. DATA 12
- TO HI SIDE OF 14
- 87654321 17
- 4285/4286 18
- VIP MODULE 18
- TERMINALS 19
- ON CONTROL 19
- 4285 or 4286 20
- Programming Overview 21
- Data Field Programming 25
- (Secondary) 27
- 1st entry 31
- (2nd entry) 31
- Zone Programming 35
- Testing the Zones 37
- (Yellow) 38
- Output Device Programming 45
- Zone Lists 49
- Alpha Descriptor Programming 51
- (Word Space) 54
- System Communication 55
- System Operation 59
- OFF AWAY STAY 60
- CODE CHIME 60
- MAX TEST BYPASS 60
- Testing the System 61
- Troubleshooting Guide 64
- Remote Programming and 67
- Control (Downloading) 67
- SECTION 13 69
- Regulatory Agency Statements 73
- UL NOTICES 74
- Limitations and Warranties 75
- ADEMCO LIMITED WARRANTY 76
- Index-1 77
- WARNING: 79
- ¬19^l 80
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA 10
(80 strony)
(132 strony)Maxon SP-200K Series manuels
Manuels d'utilisation et guides de l'utilisateur pour Les radios bidirectionnelles Maxon SP-200K Series.
Nous fournissons des manuels en pdf 1 Maxon SP-200K Series à télécharger gratuitement par type de document : Instructions d'exploitation
Komentarze do niniejszej Instrukcji