ADEMCO VISTA 10 Instrukcja Konfiguracji Strona 39
- Strona / 80
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Section 5 - Zone Programming
5–5
✱
58 Expert Programming Mode Procedures
This method is designed for use by installers with previous experience in programming control panels.
Zone Programming involves:
1. Entering the programming mode by pressing
✱
20
2. Pressing
✱
22 (RF System) to enable reception of 5800 series transmitters
3. Pressing
✱
58 to start expert mode zone programming
4. Making appropriate entries at the prompts
5. Confirming the serial number of wireless transmitter zones.
The following prompts are displayed:
PROMPT VALID ENTRIES EXPLANATION
SET TO CONFIRM?
0 = NO 1 = YES 0
Set to Confirm
0 = no
1 = yes
This display appears upon entry into
✱
58 mode. The default is
0
(No). If you enter
1
(Yes), you are prompted to confirm each
transmitter after entering the serial and loop numbers (at the
XMIT
TO CONFIRM
prompt later in this procedure).
We recommend that you confirm the programming of every
transmitter.
Zn
ZT – RC In: L
01 09 – 10 HW: 1
Summary Screen
01-25 = Zone number
00 = Quit
[
✱
] to continue
OR
A summary screen appears, showing zone 01’s current programming
or default values.
Zn
ZT – RC In: L
10 –
– –
: –
[D to go to prompts for
wireless key programming
templates]
Enter the zone number being programmed, then press [
✱
], which
displays a summary screen for that zone. See next prompt (in this
example, zone 10 is being entered). You must always program zones
using two digits.
If programming a wireless key,
press the [D] key, then skip to
the “
T
o Enter and Duplicate Wireless Keys” paragraph on a
following page in this section. When [D] is pressed, you can choose
from a series of preset templates for easy programming of wireless
key zones.
When all zones have been programmed, press “00” at this prompt to
quit this menu mode.
A summary screen with the selected zone’s current programming appears.
Zn
ZT – RC In: L
10
00 – 10
RF: 1
†
If you enter HW
(hardwired), the next
screen is similar to the one
above, except that HW is
displayed under “IN.”
Zone Programming
ZT = see Zone Type chart
shown in
✱
56 Menu
Mode
“Zone Type” prompt
RC = 1 (send CID report)
0 (no report)
IN = input type
L = loop number
[
✱
]
to continue
Begin programming zone information as follows:
•
Enter Zone Type (ZT), Report Code (RC), and Input Device
Type (I (IN)
†
sequentially, but
not
the Loop No. (L).
•
Use the [A] (Advance) and [B] (Back) keys on the keypad to
move the cursor within the screen.
•
Use the [C] key to copy the previous zone's attributes.
Press [
✱
] to save the programming and continue to the serial
number/loop number prompt. If needed, you can press the [#] key
to back up without saving.
10 INPUT S/N: L
AXXX-XXXX
1
Serial and Loop
Number
S/N = serial number
L = loop number
[
✱
]
to continue
Manually enter the serial number (found on the transmitter label),
by typing digits in the “X” locations, using the [A] (advance) or [B]
(back) keys as required. You can also open and close the transmitter
to transmit the serial number. For button-type transmitters, that
means pressing and releasing the transmitter's button.
Note
:
If you want to copy the previous zone’s serial number, press
the [C] key.
The cursor advances to the "L". Enter the loop number
Press [
✱
] to accept the existing serial and loop number.
- 6HFXULW\6\VWHP 1
- Table of Contents 3
- (if used) 4
- (if programmed) 4
- List of Figures 5
- Introduction 7
- SECTION 2 9
- DETAIL A 10
- DETAIL B 10
- KEYPAD CONNECTOR CABLE 11
- AUX. DATA 12
- TO HI SIDE OF 14
- 87654321 17
- 4285/4286 18
- VIP MODULE 18
- TERMINALS 19
- ON CONTROL 19
- 4285 or 4286 20
- Programming Overview 21
- Data Field Programming 25
- (Secondary) 27
- 1st entry 31
- (2nd entry) 31
- Zone Programming 35
- Testing the Zones 37
- (Yellow) 38
- Output Device Programming 45
- Zone Lists 49
- Alpha Descriptor Programming 51
- (Word Space) 54
- System Communication 55
- System Operation 59
- OFF AWAY STAY 60
- CODE CHIME 60
- MAX TEST BYPASS 60
- Testing the System 61
- Troubleshooting Guide 64
- Remote Programming and 67
- Control (Downloading) 67
- SECTION 13 69
- Regulatory Agency Statements 73
- UL NOTICES 74
- Limitations and Warranties 75
- ADEMCO LIMITED WARRANTY 76
- Index-1 77
- WARNING: 79
- ¬19^l 80
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA 10
(80 strony)
(132 strony)Philips 15PF5120/28B manuals
Owner’s manuals and user’s guides for Video Philips 15PF5120/28B.
We providing 1 pdf manuals Philips 15PF5120/28B for download free by document types: User Manual
Komentarze do niniejszej Instrukcji