ADEMCO Security System VISTA-15CN Instrukcja Konfiguracji Strona 81
- Strona / 132
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Section 16 - Zone Programming
16–5
Zn
ZT RC In: L
01 09
10 HW: 1
A summary screen appears, showing zone 01’s current
programming or default values.
Zn
ZT RC In: L
10 – – – : –
Enter the first digit of the zone number to be programmed. In the
example at the left, where zone 10 is to be programmed, the first
digit 1 is entered, followed by the 2nd digit 0. The display includes
dashes, as shown at left. If zone 8 were to be programmed, you
would press the 0 key, then the 8 key. You must always program
zones using two digits.
Use the [D] key to enter wireless keys. When the [D] key is
pressed, a special prompt is displayed that offers a series of default
templates for wireless keys. Go to the paragraph on page 16-7
titled “To Enter and Duplicate Wireless Keys” for the necessary
procedure.
Zn
ZT RC In: L
10 00 10 RF:
1
†
If you enter HW
(hardwired) or AW
(Auxiliary) for Input Device
Type, the next screen is
similar to the one above,
except that HW or AW is
displayed under “In.”
If you enter RF, BR, or UR,
a prompt for Serial and
Loop number is displayed,
as shown below.
↓
10 INPUT S/N: L
AXXX-XXXX 1
10 INPUT S/N: L
A022-4064
1
A display with that zone’s current programming appears.
Press [
✱] to continue.
Enter Zone Type (ZT), Report Code (RC), and Input Device
Type (In)
†
sequentially, but not the Loop No. (L).
Use the [A] (Advance) and [B] (Back) keys on the keypad to move
the cursor within the screen.
Use the [C] key to copy the previous zones attributes.
Press [
✱] if the existing information is acceptable. If not, you can
press the [#]
key to back up without saving.
Manually enter the serial number (found on the transmitter
label), by typing digits in the “X” locations, using the [A]
(advance) or [B] (back) keys as required. You can also perform
two open and close sequences; for button-type transmitters, that
means pressing and releasing the button twice.
NOTE:
If you want to copy the previous zone’s serial number,
press the [C] key.
Press [
✱] to advance to the loop number, then enter loop number.
Press [
✱] to accept the existing serial and loop number. If neces-
sary, press [#] to back up and re-enter or edit the serial number
before pressing [
✱] to save.
To Delete a Serial
Number →→
To delete an existing serial number, enter 0 in the loop number
field. The serial number changes to all 0's as shown.
10 INPUT S/N:
L
A000-0000 0
If you entered 0 in error, simply re-enter the loop number. The
serial number then returns to the display.
Press [
✱] to accept.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15CN
(20 strony)Philips 15PF5120/28B manuals
Owner’s manuals and user’s guides for Video Philips 15PF5120/28B.
We providing 1 pdf manuals Philips 15PF5120/28B for download free by document types: User Manual
Komentarze do niniejszej Instrukcji