ADEMCO Security System VISTA-15CN Instrukcja Konfiguracji Strona 108
- Strona / 132
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
VISTA-15/VISTA-15CN Installation and Setup Guide
22–4
Relay/Powerline Carrier Device Activation
If relay outputs (via a
4204
or
4229
) or
Powerline Carrier devices
are used, two keypad
entries available to the user are included. They can manually activate or deactivate the
device(s) for starting or stopping some action, such as turning lights on or off, etc.
These keypad entries are:
[Security Code] + [#] + [7] + Device No. activates (starts) that device.
[Security Code] + [#] + [8] + Device No. deactivates (stops) that device.
4285/4286 VIP Module (if used)
Refer to the separate instructions supplied with the VIP module for information concerning
its operating procedures.
The VIP (phone module) cannot be used to add user codes in this system. User codes must be
added by using a wired keypad.
Exit Error Alarm Displays (if programmed)
•
A display of
CANCELED ALARM
or
CA
and a zone indication appears if an exit or
interior zone contained a fault during closing at the time the Exit Delay ended (e.g., exit
door left open), but the system was disarmed during the Entry Delay time. The alarm
sounder and keypad sound continuously, but stop when the system is disarmed. No
message is transmitted to the Central Station.
•
A display of EXIT ALARM or EA and a zone indication appears when the Exit Delay
ends if an exit or interior zone contained a fault during closing. The alarm sounder and
keypad sound continuously until the system is disarmed (or timeout occurs). An "Exit
Alarm" message is sent to the Central Station.
•
The EXIT ALARM display and zone indication also results if an alarm from an exit or
interior zone occurs within 2 minutes after the end of an Exit Delay.
In any of the above cases, use a second Off sequence (code plus OFF key) to clear the display.
Trouble Condition Displays
The word
CHECK
on the keypad's display, accompanied by a rapid beeping at the keypad,
indicates that there is a trouble condition in the system. Pressing any key silences the
audible warning sound. A Trouble report is sent to the Central Station, if programmed.
Instruct users to call for service immediately upon seeing any of the following messages. (See
Section 24: Troubleshooting Guide
also.)
CHECK and BATTERY Displays
A display of
CHECK
and one or more zone numbers
indicates that a problem exists with the
displayed zone(s) and requires attention in the disarmed state for the following conditions:
•
If control
senses
a high resistance in the loops on hardwired zones 2–6 it displays
CHECK and the affected zone number.
•
A display of
CHECK
and
09
indicates that communication between control and a zone
expander or wireless receiver is interrupted. Check the wiring and/or DIP switch settings
on the units.
•
If there are wireless sensors in the system, the
CHECK
condition may also be caused by
some change in the environment that prevents the receiver from receiving signals from a
particular sensor.
•
If control
senses
a short in the loops on hardwired zones 2–6 (If Hardwire Short
Detection is enabled in
✱
30), it displays CHECK and the affected zone number. Unlike
the other CHECK conditions above, this Hardwired Short detection does not produce an
audible sound at the keypad.
- 9,67$ 1
- 9,67$&1 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- Installing the Control 13
- V15-01-V0 14
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Section 12: Final Power-Up 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–6 23
- 2000 OHMS 24
- Programming Hardwired Zones 26
- Wired Zone Expansion 27
- DISARMED 29
- READY TO ARM 29
- Wireless Expansion 31
- < < 32
- Installing the 5800TM Module 33
- Jam Detection and Reporting 33
- Appendix A 36
- 1 2 3 4 5 37
- Powerline Carrier Devices 41
- Programming Relay Outputs 42
- 4285 & 4286 VIP Module 43
- Section 11: 44
- Audio Alarm 44
- Verification (AAV) Unit 44
- 4285 or 4286 45
- VIP MODULE 45
- External Sounders 47
- Sounder Connections and Power 48
- Sounder Supervision 48
- Testing the Sounder 48
- Long Range Radio 49
- Dynamic Signaling Feature 50
- 1 2 3 4 5 6 52
- Final Power-Up 53
- Battery Tests 54
- Mechanics of Programming 55
- Loading Factory Defaults 57
- Exiting the Programming Mode 57
- Section 18. Zone Lists 61
- Data Field Descriptions 63
- ZONE SOUNDS & 65
- TIMING ( 65
- Interactive 69
- Zone Programming 77
- 79
- To Remove a Zone 82
- Section 16 - Zone Programming 85
- Output Device Programming 87
- Zone Lists 93
- Cross Zoning - Zone List 04 94
- NIGHT-STAY - Zone List 05 94
- Alpha Descriptor Programming 95
- Summary Mode Display 96
- ALPHA VOCABULARY LIST 98
- CHARACTER (ASCII) CHART 98
- Remote Programming and 99
- Control (Downloading) 99
- Initial Download 100
- Remote Programming Commands 100
- System Communication 101
- FORMAT TYPE DESCRIPTION 102
- System Operation 105
- Keypad Functions 106
- Setting the Real-Time Clock 110
- Testing the System 111
- Troubleshooting Guide 113
- SMOKE DETECTOR 114
- CONTACTING TECHNICAL SUPPORT 115
- In This Section 117
- APPENDIX A 121
- Regulatory Agency Statements 123
- Warnings and Limitations 125
- VISTA-15/VISTA-15CN 131
- SUMMARY OF CONNECTIONS 131
- Copyright 132
- 2000 PITTWAY CORPORATION 132
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15CN
(20 strony)Philips 15PF5120/28B manuals
Owner’s manuals and user’s guides for Video Philips 15PF5120/28B.
We providing 1 pdf manuals Philips 15PF5120/28B for download free by document types: User Manual
Komentarze do niniejszej Instrukcji