ADEMCO VISTA-128B Instrukcja Konfiguracji Strona 231
- Strona / 252
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
A-1
APPENDIX A.
Regulatory Agency Statements
•••••••••••••••••••••••••••••••••••••••••••••••••
UL Installation Requirements
The following requirements apply to both UL residential and UL commercial burglary
installations:
1. All partitions must be owned and managed by the same person(s).
2. All partitions must be part of one building at one street address.
3. The audible alarm device(s) must be placed where it/they can be heard by all partitions.
4. The control cabinet must be protected from unauthorized access. This can be done by
installing a tamper switch on the cabinet door (not supplied with VISTA-128B) or by
installing a UL Listed passive infrared detector positioned to detect cabinet access. Wire
the selected device to any EOLR-supervised zone (Zone 1-8). Program this zone for day
trouble/night alarm (type 05) or 24-hour audible alarm (type 07) response. The 24-hour
alarm response must be used for multiple partitioned systems.
5. Remote downloading and auto-disarming are not UL Listed features.
UL609 Grade A Local Mercantile Premises/Local Mercantile Safe & Vault
1. Use the VISTA-128B.
2. All zones must be configured for EOLR supervision (*41=0). Wireless sensors may not be
used. If 4190WH RPMs are used, set field *24 to "0" to enable tamper detection.
3. Attach a door tamper switch (supplied) to the VISTA-128B cabinet backbox. For safe and
vault installations, a shock sensor (not supplied) must also be attached to the backbox.
(Also see
Mounting the Cabinet
in the
Installing the Control
section)
4. Wire an ADEMCO AB12 Grade A Bell/Box to the bell output. Bell wires must be run in
conduit. Program the bell output for 16 or longer timeout and for confirmation of arming
ding. (Also see the
External Sounders
section)
5. Wire the VISTA-128B tamper switch and AB12 Bell/Box tamper switches to any EOLR
supervised zone (zones 1-8). Program this zone for day trouble/night alarm (type 05) or
24-hour audible alarm (type 07) response. The 24-hour alarm response must be used for
multiple partitioned systems.
6. Entry delays must not exceed 45 seconds, and exit delays must not exceed 60 seconds.
UL365 Police Station Connected Burglar Alarm
Follow the instructions for UL609 local installations given above.
For Grade A Service:
• You may use the VISTA-128B dialer alone, or the 7720 Long Range Radio alone.
• When using the dialer, program it to send Burglary Alarm, Low Battery and
Communicator Test reports. Field *27 must be set to "024" (or less) so that test reports
are sent at least once every 24 hours.
• If using the 7720, connect it to the VISTA-128B burglary/audible panic alarm trigger.
- VISTA-128B 1
- K3500-3 7/98 2
- Table of Contents 9
- List of Figures 14
- How To Use This Manual 15
- General Description 17
- Wireless 18
- Zone Expansion 18
- Planning a Partitioned System 23
- Common Lobby Logic 24
- MAIN ENTRANCE 25
- OFFICE #1 OFFICE #2 25
- COMMON LOBBY 25
- Codes with Global Arming 26
- Codes with Non-Global Arming 26
- Cross-Zoning 30
- Call Waiting Defeat Logic 31
- Installing The Control 33
- Installing The Keypads 37
- Figure 5-2 38
- #93 Menu Mode 39
- Basic Hardwired Zones 001-009 41
- Figure 6-3 43
- DISARMED 45
- READY TO ARM 45
- DISARMED Press 46
- 2-Wire Polling Loop Expansion 47
- (Zones 010 - 128) 47
- Wire Gauge Max. Length 48
- #22 gauge 650 feet 48
- #20 gauge 950 feet 48
- #18 gauge 1500 feet 48
- #16 gauge 2400 feet 48
- Power Up Procedure 49
- Extension Loop #1 50
- Extension Loop #2 50
- Extension Loop #8 50
- Wireless Zone Expansion 55
- Relay Outputs and 63
- Powerline Carrier Devices 63
- Relay Programming 66
- #93 Menu Mode 66
- 4285/4286 VIP Module 67
- Mounting the VIP Module 68
- Wiring the VIP Module 68
- 1 23456 7 69
- 4 3 2 1 73
- The Mechanics of 74
- Programming 74
- J7 Trigger Outputs 75
- Ground Start Trigger Setup 76
- The Mechanics o 77
- 1 2 3 4 5 6 7 8 9 78
- Event Log Printer Connections 82
- 7820 Long Range Radio 83
- Wiring the Long Range Radio 84
- Trouble Messages 85
- Access Control 87
- Access Control Dialer Events 90
- External Sounders 91
- Alarm Output Supervision 92
- Wiring the Alarm Output 93
- Programming the Alarm Output 94
- Event Log Options 95
- Supplied with 96
- Programming Event Log Options 97
- Event Logging Procedures 97
- CLEAR EVENT LOG 99
- 0=NO 1=YES 99
- 0=NO 1=YES 99
- 4100APG Pager Interface 101
- Wiring the 4100APG 102
- 4100APG LED Indications 104
- Final Power-Up Procedure 105
- 4142TR CABLE 106
- Cannot exceed 128MA 107
- Connecting The Battery 109
- The Mechanics of Programming 111
- Viewing Data Fields 112
- Entry Errors 112
- #93 Menu Mode Programming 114
- Zone Type Definitions 115
- Zone Index/Zone Type Defaults 119
- Zone Type Defaults 120
- Data Field Descriptions 121
- 95 96 99 122
- 95 96 99 Duress 129
- Enter 00-09; B-F (11-15) 130
- [15 15 15 15] 130
- Alm Chck Byps O/C Systm Test 134
- F B S 137
- Zone Programming 141
- 010 LEARN S/N? 145
- 1 = YES, 0 = NO 1 145
- Sequential Mode Programming 147
- Zone Number Entered 148
- 010 INPUT S/N 149
- A 022-4064 149
- Serial # 149
- 010 CONFIRMED SL:1 149
- A022-4064 149
- REPORT CODE PROG 150
- 1 = YES 0 = NO 0 150
- QUIT REPORT MENU 154
- 1 = YES 0 = NO 0 154
- QUIT MENU MODE? 154
- 1 = YES 0 = NO 0 154
- Relay Voice Descriptors 158
- Device Programming 159
- SOUND OPTION 160
- KEYPAD GLBL? 160
- RF EXPANDER 160
- HOUSE ID XX 160
- SUPERVISED CF? 160
- SPACE ENTER 161
- MODULE PART 163
- Zone List Programming 168
- RF Serial Number Clear Mode 171
- CLEAR RF SERIAL#? 172
- 1 = YES, 0 = NO 0 172
- ARE YOU SURE? 172
- 1 = YES, 0 = NO 0 172
- Scheduling Options 173
- Time Window Definitions 175
- Open/Close Definitions 176
- Scheduling Menu Mode 178
- Scheduling Menu Structure 179
- Time Windows 180
- Daily Open/Close Schedules 181
- Holiday Schedules 182
- Time-Driven Events 183
- Relay No. if 4204 relays 185
- Timed Events ? 185
- 1 Yes 0 = No 0 185
- TIMED EVENT # ? 185
- 01-20, 00=Quit 01 185
- 50=Off-normal Reminder 187
- Temporary Schedules 189
- User Scheduling Menu Mode 191
- In This Section 193
- A Successful Transmission 194
- Reporting Formats 194
- Downloading Primer 205
- On-Line Control Functions 207
- Access Security 207
- PRINTER DTR 208
- Setting The Real-Time Clock 209
- User Access Codes 211
- OK TO DELETE 003? 217
- 0=NO 1=YES 217
- Keypad Functions 219
- ARM ALL ? 220
- 0 = NO , 1 = YES 220
- Closing Delay ? 221
- Hit 0-2 Hours 221
- Part. 1 A0 222
- User 01 Auth.=1G 222
- ENTER SPEED KEY # 223
- 01-32 00=QUIT 223
- ENTER DEVICE NO 224
- 00=QUIT 01 224
- HIT THE "*" KEY 225
- HIT 0=OFF , 1=ON 225
- Testing The System 227
- Armed Burglary System Test 228
- Trouble Conditions 228
- To the Installer 230
- Regulatory Agency Statements 231
- Requirements 232
- DIP Switch Tables 235
- 4275 PIR 237
- 4194 REED CONTACT 237
- (SURFACE MOUNT) 237
- 4278 PIR 237
- Summary of System Commands 239
- Specifications 241
- WARNING! 249
- ¬.l 251
- Copyright 252
- 1998 PITTWAY CORPORATION 252
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA-128B
(40 strony)Whirlpool ECM 532 U manuales
Manuales del propietario y guías del usuario para Lavaplatos Whirlpool ECM 532 U.
Ofrecemos 1 manuales en pdf Whirlpool ECM 532 U para descargar gratis por tipos de documentos: Instrucciones de uso
Komentarze do niniejszej Instrukcji