ADEMCO VIA 30+ Instrukcja Naprawy Strona 49
- Strona / 104
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
7 –5
02 Start: Zn Typ
Not Used 00
If a zone type or system operation will be used to START the relay action,
enter the appropriate two-digit code (see table that follows). If not, enter 00.
Press the [
✱
] key to continue.
CHOICES FOR ZONE TYPES
00 = Not Used 05 = Trouble Day/Alarm Night 08 = 24 Hr Aux
01 = Entry/Exit 06 = 24 Hr Silent 09 = Fire
03 = Perimeter 07 = 24 Hr Audible 10 = Interior w/Delay
04 = Interior Follower
CHOICES FOR SYSTEM OPERATION
20 = Arming–Stay 33 = Any Burglary Alarm 39 = Any Fire Alarm
21 = Arming–Away 34 = Code + # + 7 Key Entry 40 = Bypassing
22 = Disarming (Code + OFF) 35 = Code + # + 8 Key Entry 41 = AC Power Failure
31 = End of Exit Time 36 = At Bell Timeout** 42 = System Batt. Low
32 = Start of Entry Time 38 = Chime 58 = Duress
**Or at Disarming, whichever occurs earlier.
02 Stop: Zn List
No List 0
If a zone list will be used to STOP, or restore, the relay action, enter the zone list
(ZL) number 1, 2, or 3 (to be programmed in
✱
81 mode). If not used, enter 0.
Press the [
✱
] key to continue.
02 Stop: Zn Typ
Not Used 00
If a zone type or system operation will be used to STOP the relay action, enter
the appropriate two digit code (see the "ZT" choices listed above). If not, enter
00. Press the [
✱
] key to continue.
02 A EV ZL ZT
STT 0 0 0 00
This screen again displays a summary of the current relay START
programming.
Press the [
✱
] key to continue.
02 A EV ZL ZT
STP – – 0 00
This screen again displays a summary of the current relay STOP programming.
Press the [
✱
] key to continue.
The display then returns again to the first screen so that the next relay number
to be programmed can be entered, or enter [0][0] to end relay programming.
Previously entered data can be reviewed by pressing [#] [8] [0]. After the
relay number is chosen, press [
✱
] to go to the next screens. This is a review
mode only, and data cannot be changed.
Example of
Output Relay
Programming
A lamp is to be turned on when any one of 3 specific zones are faulted or
when any 24-hour auxiliary zone is disturbed. We want to turn off the
lamp manually without affecting the arming status of the system.
In field *80 we choose Output Relay 01 and program the Action (A) to be "2"
(Close and stay closed). The Event we are looking for to
start
the relay action
is a fault, so we will program "2" in (EV). We will use Zone List 1 for the 3
specific zones, so will program "1" in (ZL), (and will program these 3 zones in
field *81's Zone List 1).
The second condition for turning on the indicator is triggering a 24 hour aux.
zone (Zone Type 08), so we will program (ZT) as "08".
To
stop
relay action and turn off the indicator, we do not want to use a restore
of any zone, so we will program a "0" for the "
Restore
of"
Zone List (ZL). To
choose a manual entry of User Code + [#] + [7] to turn it off, we will program
(ZT) as "34".
If no other relay is to be programmed, go to field *81 and program the 3
specific zones in Zone List 1.
- Security System 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- HOW TO USE THIS MANUAL 7
- TERMINALS 13
- ON CONTROL 13
- 17 18 19 20 21 13
- POWER UP 15
- AUX AUX. DATA DATA 17
- – + IN OUT 17
- System Sensor 20
- RESPONSE TYPE DEFINITIONS 20
- Location 23
- Supervision 23
- Zone Information 23
- SYSTEM COMMUNICATION 24
- ALPHA DESCRIPTION PROGRAMMING 25
- (Continued) 25
- (5700 AND 5800 RF SYSTEMS) 27
- ZONE RESPONSE TYPE 30
- DEFINITIONS 30
- IMPORTANT 31
- SET SWITCHES WITH 31
- BATTERY REMOVED 31
- ✱24, and the wireless key 32
- ✱24. (RF HOUSE ID CODE) 33
- ✱24, and the 33
- Example: 34
- SYSTEM COMMUNICATIONS 34
- ALPHA DESCRIPTOR PROGRAMMING 35
- ✱56 mode 36
- ✱24 is necessary only if 36
- responses (e.g. 37
- Loop 1: 38
- Loop 2: 38
- Loop 3: 38
- functions as wired keypads 38
- SEQUENTIAL 39
- – RC In: L 39
- SEQUENTIAL MODE 40
- Section 14 40
- – 00 RF: 1 s 41
- Section 14: SEQUENTIAL MODE 41
- Relay Device Basics 45
- 4204 and 4229 Relay Modules 45
- Programming Options Defined 46
- restores 47
- Output Relay Displays 48
- (1 sec ON, 1 sec OFF) 48
- Zone List Displays 50
- Section 8. 4285 PHONE MODULE 51
- Not Used 52
- VOICE MODULE 53
- Section 9. EXTERNAL SOUNDERS 57
- Section 10. LONG RANGE RADIO 59
- INSTALLING THE CONTROL 63
- SYSTEM OPERATION 63
- TROUBLESHOOTING GUIDE 63
- Section 13 65
- ✱ ZN 01 ZONE 01 66
- ✱ ZN 01 A 66
- ✱ ZN 01 B ACK 66
- ✱ ZN 01 BACK 66
- ZN 01 BACK 67
- ALPHA VOCABULARY LIST 69
- Section 14. SEQUENTIAL MODE 71
- Serial #↑ 72
- TESTING THE SYSTEM 73
- Examples: 79
- TESTING THE SYSTEM 81
- TO THE INSTALLER 84
- Section 17. SYSTEM OPERATION 85
- Assigning the Master Code 86
- Panic Keys 86
- SMOKE DETECTOR 90
- WWW. ADEMCO. COM 91
- @ Ademco–165 . Ademco . com 91
- FINAL POWER UP 93
- Ademco VIA-30PSE 94
- 4285 PHONE MODULE 95
- APPENDIX A: 97
- REGULATORY AGENCY STATEMENTS 97
- UL NOTICES 98
- (DOC) STATEMENT 99
- APPENDIX B: 101
- ADEMCO LIMITED WARRANTY 102
- VIA-30PSE 103
- N7225V2 4/97 104
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VIA 30+
(84 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji