ADEMCO VIA 30+ Instrukcja Naprawy Pobierz pdf (Strona 39)

6 –13

Enrolling 5800 Transmitters Into The System

There are two methods that may be used to enroll transmitters. The first method is performed

✱

56 zone programming mode (which is contained in this section) and describes how to enroll

each transmitter into the system as you are entering the zone information.

The second method is called "sequential mode" and uses

✱

83 (described in the

SEQUENTIAL

MODE

section later in this manual. This section describes how to enroll all the transmitters into

the system

after all zone information has been entered

As an option, the zone programming and sequential modes allow you to use a 5803 or 5804

button-type transmitter as a "program tool." The advantage of using a program tool is that it

tells the control that you are about to enroll a transmitter into the system. You can move to the

physical location of the transmitter to be enrolled, press the upper left-hand button of the

program tool, and then trip the intended transmitter (see step 10 for operation). This helps to

prevent random signals from being accepted into the system until you are ready to enroll the

intended transmitter.

The transmitter that you use as the program tool can also be used as a transmitter in the

system. If you plan to use an existing transmitter, it must first be enrolled into the system as its

associated zones. You may then program it as the tool.

Enrolling Through Zone Programming (

✱

56)

1. Enter Programming mode [Installer Code] + 8 + 0.

Enter Zone Programming by pressing

✱

56. If the system has been set

up to use 5800 series RF, and a program tool has been entered, skip

to step 4. If no program tool has been entered, the following prompt

will appear:

Program Tool?

0 = No, 1 = Yes 0

2. If a program tool is being used, enter "1." If not using a tool, enter "0"

and skip to Step 4.

00 Input S/N: L

A X X X–X X X X

3. If "1" is entered, the system will prompt for the unit’s serial number.

Enter the program tool’s serial number using one of the following

methods:

a) Enter the 7-digit serial number for the transmitter

b) Press any button on the transmitter. The keypad should beep twice

and display the serial number of the tool.

00 Input S/N: L

A123-4567 3

In this example, the serial number is A123-4567. Once enrolled, the

upper left-hand button of the program tool can be pressed to ready the

system for enrolling a transmitter into the system.

Pressing the [#] key on the keypad will cause the system to back up to

the “Program Tool ?” prompt.

The serial number for the program tool will only remain in the

system until the programming mode is exited. (Entering

✱

97 will

not delete the tool.)

Press [

✱

] to continue.

Enter Zn Num.

(00 = Quit) 10

Zone 10 entered

↑

4. Enter the zone number that you wish to program. As an example, zone

10 is shown here.

Press [

✱

] to continue.

ZN ZT – RC In: L

10 00 – 00 RF: 1

5. A display will appear, showing a summary of that zone's programming.

If the zone is not programmed, the display will appear as shown here. If

checking a zone's programming, and it is programmed satisfactorily,

press [#] to back up one step and enter another zone number, if

desired. Otherwise, press [

✱

] to continue.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 103 104

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO VIA 30+ Instrukcja Naprawy Strona 39

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VIA 30+