ADEMCO VIA 30+ Instrukcja Naprawy Strona 48
- Strona / 104
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
7 –4
If a relay is energized before a 4-wire smoke detector is
reset, the relay will be stopped by the interruption of Aux.
Power that resets the smoke detector. If this is not desired,
the power to the relay unit should be supplied from another
12V power source (e.g., the same source that is powering ex-
ternal equipment through the relay contacts).
Programming Output Relays
1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the
keypad terminals on the control, power up the system temporarily. If you
had previously connected the AC transformer to the control panel, you
need only plug in the transformer (to 120VAC outlet) to power up the
system.
2. Enter the programming mode by keying the following on the Alpha keypad:
INSTALLER code (4 1 1 1) + 8 + 0.
Field
✱
25 OUTPUT MODULE must have been programmed for a 4204 module
(enter “3”).
3 Press
✱
80. Note that this is an interactive menu programming mode. It is
used to program all output relays used in the system (4204 Relay
modules). Refer to the Programming Form worksheet in the separate
PROGRAMMING GUIDE for
✱
80 Interactive Mode.
Output Relay Displays
Enter Relay No.
(00 = Quit) 01
Upon pressing
✱
80, this screen will appear. Enter the Relay Number 01, 02,
03, or 04 for a 4204 (or 00 to end these entries). Press the [
✱
] key to
continue.
The [
✱
] key is used to accept an entry and advance to the next prompt. The
[#] key is used to revert back to the last question to check or change an
entry. Press [
✱
] to go forward again.
02 A EV ZL ZT
STT 0 0 0 00
This screen displays a summary of the current Relay START programming
(for this example, relay 02 has been selected).
Press the [
✱
] key to continue.
02 A EV ZL ZT
STP – – 0 00
This screen displays a summary of the current Relay STOP programming.
Press the [
✱
] key to continue.
02 Relay Action
No Response 0
Enter the desired relay action as listed below. Press the [
✱
] key to continue.
0 = No response 2 = Close and Stay Closed
1 = Close for 2 seconds 3 = Continuous Pulse on & off (1 sec ON, 1 sec OFF)
02 Start Event
Not Used 0
Enter the event to START the relay:
0 = Not used; 2 = Fault; 1 = Alarm; 3 = Trouble
A zone list must be used in conjunction with an event. If a zone type/system
operation is to be used instead of an event, enter 0.
Press the [
✱
] key to continue.
02 Start: Zn List
No List 0
If a zone list will be used to START the relay action, enter the zone list number
(to be programmed in field
✱
81): 1, 2, or 3. If not used, enter 0. Press the [
✱
]
key to continue.
- Security System 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- HOW TO USE THIS MANUAL 7
- TERMINALS 13
- ON CONTROL 13
- 17 18 19 20 21 13
- POWER UP 15
- AUX AUX. DATA DATA 17
- – + IN OUT 17
- System Sensor 20
- RESPONSE TYPE DEFINITIONS 20
- Location 23
- Supervision 23
- Zone Information 23
- SYSTEM COMMUNICATION 24
- ALPHA DESCRIPTION PROGRAMMING 25
- (Continued) 25
- (5700 AND 5800 RF SYSTEMS) 27
- ZONE RESPONSE TYPE 30
- DEFINITIONS 30
- IMPORTANT 31
- SET SWITCHES WITH 31
- BATTERY REMOVED 31
- ✱24, and the wireless key 32
- ✱24. (RF HOUSE ID CODE) 33
- ✱24, and the 33
- Example: 34
- SYSTEM COMMUNICATIONS 34
- ALPHA DESCRIPTOR PROGRAMMING 35
- ✱56 mode 36
- ✱24 is necessary only if 36
- responses (e.g. 37
- Loop 1: 38
- Loop 2: 38
- Loop 3: 38
- functions as wired keypads 38
- SEQUENTIAL 39
- – RC In: L 39
- SEQUENTIAL MODE 40
- Section 14 40
- – 00 RF: 1 s 41
- Section 14: SEQUENTIAL MODE 41
- Relay Device Basics 45
- 4204 and 4229 Relay Modules 45
- Programming Options Defined 46
- restores 47
- Output Relay Displays 48
- (1 sec ON, 1 sec OFF) 48
- Zone List Displays 50
- Section 8. 4285 PHONE MODULE 51
- Not Used 52
- VOICE MODULE 53
- Section 9. EXTERNAL SOUNDERS 57
- Section 10. LONG RANGE RADIO 59
- INSTALLING THE CONTROL 63
- SYSTEM OPERATION 63
- TROUBLESHOOTING GUIDE 63
- Section 13 65
- ✱ ZN 01 ZONE 01 66
- ✱ ZN 01 A 66
- ✱ ZN 01 B ACK 66
- ✱ ZN 01 BACK 66
- ZN 01 BACK 67
- ALPHA VOCABULARY LIST 69
- Section 14. SEQUENTIAL MODE 71
- Serial #↑ 72
- TESTING THE SYSTEM 73
- Examples: 79
- TESTING THE SYSTEM 81
- TO THE INSTALLER 84
- Section 17. SYSTEM OPERATION 85
- Assigning the Master Code 86
- Panic Keys 86
- SMOKE DETECTOR 90
- WWW. ADEMCO. COM 91
- @ Ademco–165 . Ademco . com 91
- FINAL POWER UP 93
- Ademco VIA-30PSE 94
- 4285 PHONE MODULE 95
- APPENDIX A: 97
- REGULATORY AGENCY STATEMENTS 97
- UL NOTICES 98
- (DOC) STATEMENT 99
- APPENDIX B: 101
- ADEMCO LIMITED WARRANTY 102
- VIA-30PSE 103
- N7225V2 4/97 104
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VIA 30+
(84 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji