ADEMCO 4120XM Podręcznik Użytkownika Pobierz pdf (Strona 58)

Adding Custom

Up to 20 installer-defined words can be added to the built-in vocabulary. Each of

Words

the 20 “words” can actually consist of several words, but bear in mind that a

maximum of 10 characters can be used for each word string. To create the

custom word or word string, proceed as follows:

Enter the programming mode.

Key ●93. The following will be displayed: * ZN ??

Now

key 00 to get into the mode which will allow the custom words to be

created. The following

will be displayed: ● ED ??

In this mode, the keys perform the following functions:

[3] Advances through alphabet in ascending order.

[1] Advances through alphabet in descending order.

[6] Selects the desired letter, and moves the cursor to the right one space.

[4] Moves the cursor one space to the left.

[7] Inserts a space at the cursor location, erasing any character at that

location.

[8] Saves the new word in the system’s

memory.

[x] Returns to description entry mode.

Key the number of the custom word or word string to be created (01-20). For

example, if you are creating the first word (or word string), enter 01; when

creating the second word, enter 02, and so on. A cursor will now appear at the

beginning of the second line.

Use the [3] key to advance through the alphabet (numbers, symbols and

special characters are included). Use the [1] key to move back through the

alphabet.

/mportant: Custom words must begin with an alphabetic character. If

numbers or symbols are used as the first character, the word will not be

saved.

When you have reached the desired character, press the [6] key to select it.

The cursor will then move to the right, in position for the next character.

Repeat steps 5 and 6 to create the desired word (or words). Note that the [4]

key

can be used to move the cursor to the left if necessary, and that key [71

can be used to enter a blank (or to erase an existing character). Each word or

word string cannot exceed 10 characters.

Press the [8] key to save the custom word(s) and return to the

● ED ??

display. The custom word (or string of words) will be automatically added to

the built-in vocabulary at the end of the group of words beginning with the

same letter.

Repeat steps 4 through 8 to create up to 19 additional custom

words (or word

strings).

10. Press the [x] key to return to the

●ZN ?? display, and follow the zone

description entry procedure to assign the new words to a zone description.

11. Key

●99 to exit the zone description programming mode.

Creating A Custom

Normally, when the system is in the disarmed state, the following display is

Message Display

present on the Console.

(Installer’s Message)

****DISARMED+***

READY TO ARM

Part or all of the above message can be modified to create a custom installer

message. For example, ****DISARMED**** on the first line or READY TO ARM

on the second line could be replaced by the installation company name or phone

number for service. Note that there are only 16 character spaces on each of the

two lines. To create a custom display message, proceed as follows:

1. Enter the programming mode.

2. Key

●93. The following will be displayed: ● ZN ??

3. Key 00. The following will appeac ● ED ??

Key 00 again. The following will appea~

●***DISARMED****

READY TO ARM

-58-

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 79 80

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO 4120XM Podręcznik Użytkownika Strona 58

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO 4120XM