ADEMCO Vista-128B PLUS Instrukcja Konfiguracji Pobierz pdf (Strona 5)

– 5 –

VISTA-128BP/VISTA-250BP Programming Form

Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,

see the

Partition-Specific Fields

section for programming these fields. Standard default (*97) values are shown in brackets [ ];

otherwise, default = 0.

*00 INSTALLER CODE | | |

Enter 4 digits, 0-9 [4140]

*04 ENABLE RANDOM TIMERS

Enter 1 to make available the randomizing of pre-programmed

time driven events for each partition. [0=disable].

*05 SYSTEM EVENTS NOTIFY [0]

1=yes, (messages sent via the RS232 port).

0=no, (no messages sent).

*06 QUICK EXIT [1]

1=enable; 0=disable

Must be 0 for UL installations.

*09 ENTRY DELAY #1 [02] |

00, 02-15 times 15 seconds

Maximum "03" for UL.

SIA Guidelines: The entry delay time and Burg Alarm Comm

Delay (field *88) combined cannot exceed 1 minute.

*10 EXIT DELAY #1 [04] |

00, 03-15 times 15 seconds

Maximum "04" for UL installations.

SIA Guidelines: Minimum 45 seconds “03”.

*11 ENTRY DELAY #2 [02] |

00, 02-15 times 15 seconds (must be longer than Entry Delay

#1). Maximum "03" for UL installations.

SIA Guidelines: The entry delay time and Burg Alarm Comm

Delay (field *88) combined cannot exceed 1 minute.

*12 EXIT DELAY #2 [08] |

00, 03-15 times 15 seconds (must be longer than Exit Delay

#1). Maximum "04" for UL installations.

SIA Guidelines: Minimum 45 seconds “03”.

*13 ALARM SOUNDER DURATION [04] |

01-15 times 2 minutes. Must be minimum 16 minutes for UL

installations. SIA Guidelines: Must be minimum 6 minutes.

*14 BURGLARY OR RS232 INPUT [0]

Enter 1 to set terminal 23 as a RS232 input to enable system

to receive serial data (75 baud) via terminal 23.

Enter 0 to enable terminal 23 as burglary input for zone 9.

*15 KEYSWITCH ASSIGNMENT [0]

Enter partition in which keyswitch used,

1-8; 0=disable

*16 CONFIRMATION OF ARMING DING [0]

1=enable; 0=disable.

Must be "1" for UL Installations.

*17 AC LOSS KEYPAD SOUNDING [0]

1=yes; 0=no

*19 RANDOMIZE AC LOSS REPORT [0]

1=10-40 min; 0=normal report (about 2 min. after AC loss).

*20 VIP MODULE PHONE CODE | |

Enter 01 - 09 for the first digit; enter [00], [11]

11 for “*” or 12 for “#” for the second digit.

Must be set to "0" for UL installations.

*21 PREVENT FIRE TIMEOUT [0]

1=No timeout; 0=Timeout.

*22 KEYPAD PANIC ENABLES [001]

1=enable; 0=disable 995 996 999

*23 MULTIPLE ALARMS [1]

1=yes; 0=no

*24 IGNORE EXPANSION ZONE TAMPER [0]

1=Ignore; 0=Enable tamper for RF and RPMs.

Must be "0" for UL installations if using these devices.

*25 BURG.TRIGGER FOR RESPONSE TYPE 8 [1]

1=enable; 0=disable

*26 INTELLIGENT TEST REPORTING [0]

1=yes (no report sent if any other report was recently sent);

0=no (send report at programmed interval, field *27)

Must be 0 for UL installations.

*27 TEST REPORT INTERVAL [0024] | | |

Enter interval in hours, 0001-9999; 0000=no report;

Max. 0024 for UL installations.

*28 POWER UP IN PREVIOUS STATE [1]

1=yes; 0=no; "1" for UL installations.

*29 QUICK ARM [1]

1=yes; 0=no

*30 TOUCHTONE OR ROTARY DIAL [0]

1=TouchTone; 0=rotary

*31 PABX ACCESS CODE | | | |

00-09; B-F (11-15)

*32 PRIM. SUBS. ACCT # | | | |

Enter 00-09; B-F (11-15) [15 15 15 15]

*33 PRIMARY PHONE NUMBER

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2 second pause

*34 SECONDARY PHONE NUMBER

Enter 0-9 for each digit. Enter #11 for *, #12 for #,

#13 for 2 second pause

1 2 3 4 5 6 7 8 9 10 ... 71 72

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Vista-128B PLUS Instrukcja Konfiguracji Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Vista-128B PLUS