ADEMCO Vista-128B PLUS Instrukcja Konfiguracji Pobierz pdf (Strona 33)

– 33 –

PROMPT

EXPLANATION

01 AUI ?

1 = YES 0 = NO 0

If you selected device type 01 (alpha keypad), this prompt appears. Enter 1 (YES) if the device is an AUI

(Symphony 8112, 8122, 8132, or 8142). See the Symphony’s instructions for the installation and

operation.

Press [✱] to accept entry.

RF Expander

PROMPT

EXPLANATION

01 RF EXPANDER

HOUSE I 00

If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This

is required if you are using a wireless keypad (5827/5827BD).

Press [✱] to accept entry.

Output Relay Module

PROMPT

EXPLANATION

01 SUPERVISED CF?

If you selected device type 04 (relay module), this prompt appears. Enter 1 if the unit is a 4204CF. If not,

enter 0. If you enter 1, only Relay 1 (Output A) and Relay 3 (Output B) on each module may be programmed

for functions. This module is usually used to add two additional supervised bell outputs to the system.

Press [✱] to accept entry.

Long Range Radio

If you selected device type 6, the 6139/6160 Keypad functions similarly to the 7720PLRR Programming Tool. See

Figure 1

for

the functions of the keys on the 6139.

READYARMED

897

AB C

456

DE F

ST X

SPACE ENTER

SHIFT

BS/ESC

N/Y

SHIFT function indicated by turning on READY LED.

Figure 1: 6139 Key Functions for Programming 7820 Radio

Each key has two possible functions: a normal function and a SHIFT function. To perform a normal key function, simply press

the desired key. To perform a SHIFT key function, press SHIFT key, then press desired function key.

Normal and SHIFT key Functions:

Key Normal Key Function SHIFT Key Function

BS/ESC [BS]: Press to delete entry [ESC]: Press to quit Program Mode

Also, can reset EEPROM defaults *

↓/↑ [↓]: Scroll down programming [↑]: Scroll up programming

N/Y [N]: Press for "NO" answer [Y]: Press SHIFT-Y for "YES" answer

SHIF

Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is

pressed. Press again for each SHIFT function desired.

1/A [1]: For entering the number 1 [A]: Used for entering C.S. ID number

2/B [2]: For entering the number 2 [B]: Used for entering C.S. ID number

3/C [3]: For entering the number 3 [C]: Used for entering C.S. ID number

4/D [4]: For entering the number 4 [D]: Used for entering C.S. ID number

5/E [5]: For entering the number 5 [E]: Used for entering C.S. ID number

6/F [6]: For entering the number 6 [F]: Used for C.S. ID & FAST Mode

7/S [7]: For entering the number 7 [S]: Press to display diagnostic status

8/T [8]: For entering the number 8 [T]: Press to send TEST messages

9/X [9]: For entering the number 9 [X]: Press to reset the 7820

*/SPACE [*]: Not used with 7820 [SPACE]: Not used with 7820

0 [0]: For entering the number 0 No SHIFT function

#/ENTER [#/ENTER]: Press to accept entries No SHIFT function

* Active only when the "REVIEW?" prompt is displayed.

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 71 72

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Vista-128B PLUS Instrukcja Konfiguracji Strona 33

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Vista-128B PLUS