ADEMCO Security System VISTA-15 Dokumentacja Pobierz pdf (Strona 42)

PROMPT VALID ENTRIES EXPLANATION

10 Zone Type

Perimeter 03

Zone Type (ZT)

00-24, 77, 90, 91 = zone type

(see table at right)

Each zone must be assigned to a zone type, which defines the way in

which the system responds to faults in that zone.

Enter the Zone Type code from the list below:

Note:

If 00 is entered,

Delete Zone ?

will be displayed.

00 = Not used 07 = 24-Hr Audible 20 = Arm–STAY*

01 = Entry/exit #1 08 = 24-Hr Aux 21 = Arm–AWAY*

02 = Entry/exit #2 09 = Fire 22 = Disarm*

03 = Perimeter 10 = Interior w/Delay

23 = No Alarm Resp*

04 = Interior Follower 12 = Monitor Zone 24 = Silent Burglary

05 = Trouble Day/Alarm Night 14 = Carbon Monoxide 77 = Keyswitch

06 = 24-Hr Silent 16 = Fire w/Verify 81 = AAV Monitor Zone

*5800 button-type transmitters only 90-91 = Configurable

10 Partition

Partition No. (P)

1-3 = partition (3 = common)

[

∗

] to continue

VISTA-20P.

Enter the Partition number for this zone. Partition 1 is shown

entered.

10 Report Code

1st 01 2nd 00 10

Report Code (RC)

First Digit: 1-9, #+10 for 0, #+11

for B, #+12 for C,

#+13 for D, #+14 for

E, #+15 for F

00 to disable

Second Digit: same as above

[

∗

] to continue

Enter the report code for this zone, which consists of 2 hexadecimal

digits, each in turn consisting of 2 numerical digits. For example, for

a report code of “10,” enter 01 and 00.

For Contact ID

, entering any non-zero entry as the first digit

enables the report code for this zone. Refer to the System

Communication section for information about report codes and

formats.

02 HARDWIRE TYPE

EOL 0

Hardwire Type

0 = EOL 3 = zone doubling

†

1 = NC 4 = double-balanced

†

2 = NO

[

∗

] to continue

This prompt appears only for zone numbers 02-08.

Zone 1 is automatically set for EOL operation.

† VISTA-20P

02 Response Time

Response Time (RT)

0 = 10mSec

1 = 350mSec

2 = 700mSec

3 = 1.2 seconds

[

∗

] to continue

This prompt appears only for hard-wired zones 01-08 (zone 02 is used

as an example in display).

Option 3: used for “clean me” option on zone 1 (see field ∗174).

10 INPUT TYPE

RF TRANS 3

Input Device type (In)

2 = AW (Aux wired zone)

3 = RF (supervised RF

transmitter,

4 = UR (unsupervised RF

transmitter)

5 = Button type RF transmitter

(unsupervised).

[

∗

] to continue

This prompt is skipped for zones 1-8, or 1-16 if zone-doubling was

enabled at “Hardwire Type” prompt.

All of the RF transmitters have one or more unique factory-assigned

input (loop) ID codes. Each of the inputs requires its own

programming zone (e.g., a 5804's four inputs require four

programming zones).

RF Transmitters can be enrolled as one of the following types:

Type Description

“RF”

Sends periodic check-in signals, as well as

(Supervised RF) fault, restore, and low-battery signals. The

transmitter must stay within receiver's range.

“UR”

Sends all the signals that the “RF” type

(Unsupervised RF) does, but the control does not supervise the

check-in signals. The transmitter may therefore

be carried off-premises.

“BR”

(Unsupervised Sends only fault signals. It will not send a

Button RF) low-battery signal until it is activated. The

transmitter may be carried off-premises.

NOTE:

• For the built-in hardwired zones, the Input Device type is

automatically displayed as HW and cannot be edited.

• To change the input type of a previously programmed wireless

device (type RF, UR, BR) to a wired zone (type AW), you must first

delete transmitter’s serial number (see To Delete A Serial Number

prompt on next page)

Installation Instructions

5-2

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 87 88

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Security System VISTA-15 Dokumentacja Strona 42

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15