ADEMCO Security System VISTA-15 Dokumentacja Pobierz pdf (Strona 27)

SECTION 4

Data Field Programming

•••••••••••••••••••••••••••••••••••••••

About Data Field Programming

The following pages list this control’s data fields in numerical order. Field numbers are listed in the

left column followed by a “Title and Data Entries” column, which lists the valid entries for each field.

Experienced installers can simply follow this column when programming the data fields. The

“Explanation” column provides explanatory information and special notes where applicable.

Use the blank programming form to record the data for this installation.

Programming Data Fields

Data field programming involves making the appropriate entries for each of the data fields.

Start Data Field programming by entering the installer code + 8 + 0 + 0.

System Setup Fields (

∗

20 – ∗29)

FIELD TITLE and DATA ENTRIES EXPLANATION

*20

Installer Code

Enter 4 digits, 0-9

The Installer Code can perform all system functions except it cannot

disarm the system unless it is used to arm the system.

*21

Quick Arm Enable

0 = do not allow quick arm

1 = allow quick arm

If enabled, a user code is not needed to arm the system. Instead,

users can press the [#] followed by an arming key to arm the system.

However, the user code is always needed to disarm the system.

*22

RF Jam Option

0 = no RF jam detection

1 = send RF jam report

If enabled, a report is sent if the system detects an RF jamming

signal.

UL installations must be 1 if wireless devices are used.

*23

Quick (Forced) Bypass

0 = no quick bypass

1 = allow quick bypass (code + [6] + [#] )

All zones bypassed by this function will be displayed after the bypass

is initiated.

UL installations must be 0 (no forced bypass)

*24

RF House ID Code

00 = disable all wireless keypad usage

01–31 = House ID for partition 1, 2 and

common

The House ID identifies receivers and wireless keypads. If a 5827 or

5827BD Wireless Keypad or 5804BD Transmitter is being used, a

House ID code

must

be entered, and the keypad should be set to the

same House ID. You can assign RF house ID for each partition.

*26

Chime By Zone List 3

0 = no zone list (chimes on fault of

any

entry/exit or perimeter zone when chime

mode on)

1 = use zone list (chimes on fault of

specific

zones programmed in relay

zone list 3 when Chime mode on)

If enabled, you can define the specific zones intended to chime when

faulted while the system is in Chime mode. Use zone list 3 to assign

these zones (see

∗

Zone List Programming

section for details).

*27

Powerline Carrier Device (X-10)

House ID

0 = A 6 = G # + 11 = L

1 = B 7 = H # + 12 = M

2 = C 8 = I # + 13 = N

3 = D 9 = J # + 14 = O

4 = E # + 10 = K # + 15 = P

5 = F

Powerline Carrier devices require a House ID, identified in this field.

Program Powerline Carrier devices in interactive modes

∗

79, *80 and

*81.

Not intended for fire or UL installations.

*28

Access Code for Phone Module

1-9 = first digit of access code

∗

or # = second digit of access code (enter #

+11 for “

∗

”, or # +12 for “#”)

You need to assign a 2-digit access code for the 4285/4286 Phone

Module, if used. Example: If desired access code is 7

∗

, 7 is the first

entry, and [#] + 11 (for

∗

) is the second entry.

NOTE:

A “0” in either digit disables the phone module.

Must be “00” for UL Commercial Burglar Alarm installations.

4-1

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 87 88

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Security System VISTA-15 Dokumentacja Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15