ADEMCO Security System VISTA-15 Dokumentacja Strona 24
- Strona / 88
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Type 06
24-hour Silent Alarm
•
Usually assigned to a zone containing an emergency button.
•
Sends a report to the central station but provides no keypad display or sounding.
Type 07
24-hour Audible Alarm
•
Assign to a zone that has an emergency button.
•
Sends a report to the central station, and provides an alarm sound at the keypad,
and an audible external alarm.
Type 08
24-hour
Auxiliary Alarm
•
Assign to a zone containing an emergency button, or to a zone containing
monitoring devices such as water or temperature sensors.
•
Sends a report to the central station and provides an alarm sound at the keypad.
(No bell output is provided.)
Type 09
Supervised Fire
•
Provides a fire alarm on short circuit and a trouble condition on open circuit. A
fire alarm produces a pulsing bell output.
•
This zone type is always active and cannot be bypassed.
Type 10
Interior w/Delay
•
Provides entry delay (using the programmed entry time), if tripped when the
panel is armed in the Away mode.
•
Entry Delay 1 begins whenever sensors in this zone are violated, regardless of
whether or not an entry/exit delay zone was tripped first.
•
Bypassed when the panel is armed in the Stay or Instant modes; if armed in
Night-Stay mode, zones assigned to zone list 05 (night-stay zone list) are not
bypassed when system armed in Night-Stay mode.
Type 12
Monitor Zone
•
Works as a dynamic monitor of a zone fault/trouble (not alarm). In the case of a
short/open, the message, "*ALARM*-24 Hr. Non-Burg. -#XXX " (where XXX is
the zone number) will be sent to the Central Station. The system keypad will
display a “check” message indicating the appropriate zone (but keypad beeping
does not occur). Upon restoral of the zone, the message, "*RESTORE*-24 Hr.
Non-Burg. -#XXX
" will be sent to the Central Station.
•
The “check” message will automatically disappear from the keypad dynamically,
when the zone restores; a user code + off sequence is not needed to reset the zone.
•
Faults of this zone type are independent of the system, and can exist at the time
of arming without interference.
•
Since this is a “trouble” zone type, do not use this zone type with relays set to
activate upon “alarm.”
Type 14
24 Hour Carbon
Monoxide Monitor
•
Assigned to any zone with a carbon monoxide detector.
•
The bell output will pulse when this zone type is alarmed.
•
Always active and cannot be bypassed.
Type 16
Fire w/Verification
•
Provides a fire alarm when zone is shorted, but only after alarm verified.
•
System verifies alarm by resetting zones for 12 seconds after short is detected. A
subsequent short circuit within 90 seconds triggers fire alarm.
•
Provides a trouble response when zone is open.
Type 20
Arm-Stay (BR only)
•
Arms the system in Stay mode when the zone is activated.
•
Pushbutton units send the user number to the central station when arming or
disarming.
•
User number for button must be assigned.
Type 21
Arm-Away (BR only)
•
Arms the system in Away mode when the zone is activated.
•
Pushbutton units send the user number to the central station when arming or
disarming.
•
User number for button must be assigned.
Type 22
Disarm (BR only)
•
Disarms the system when the zone is activated.
•
User number for button must be assigned.
Type 23 *
No Alarm Response
•
Can be used on a zone when an output relay action is desired, but with no
accompanying alarm (e.g., lobby door access).
Installation Instructions
3-4
- 9,67$3366HULHV 1
- 9,67$36HULHV 1
- SOUNDING OF FIRE NOTIFICATION 2
- APPLIANCES 2
- Table Of Contents 3
- SECTION 1 5
- Capabilities 5
- Functions 5
- Compatible Devices 6
- SECTION 2 7
- Cabinet and Lock 7
- Wiring to Keypads 9
- Sounder (Bell) Connections 10
- Backup Battery 11
- Earth Ground 11
- Hardwire Zones 12
- Smoke Detectors (continued) 13
- Installing the Transmitters 14
- Installing the RF Receiver 14
- Installing a 5800TM Module 14
- Installing a Keyswitch 15
- Connecting Relay Modules 16
- Powerline Carrier Devices 17
- Installation Instructions 18
- Long Range Radio Connections 19
- AAV Connections 19
- Programming Overview 21
- Pager Programming 22
- Function Keys 23
- Output Devices 23
- Zone Type Definitions 23
- Mechanics of Programming 25
- Data Field Programming 27
- Zone Sounds & Timing ( 28
- Dialer Programming ( 29
- Miscellaneous System Fields 32
- Pager Programming Fields 35
- Symphony (AUI) Enable 39
- Keypad Programming Fields 39
- Zone Programming 41
- 43
- Completing Zone Programming 44
- Entd A022-4063 47
- Rcvd A022-4064 47
- Output Device Programming 49
- Activated By 52
- Zone List 52
- Zone Type 52
- Zone Number 53
- Output Action 53
- Output Number 53
- Summary Screen 53
- Zone Lists 55
- Function Key Programming 57
- Alpha Descriptor Programming 59
- Adding Custom Words 61
- CUSTOM WORD ? 61
- ALPHA VOCABULARY LIST 62
- Italicized 62
- Creating Schedules 63
- HH MMAM 64
- 0=NO 1=YES X 64
- System Communication 65
- Ademco Contact ID 66
- System Operation 69
- Keypad Functions 70
- Setting the Real-Time Clock 71
- Testing the System 73
- Go/No Go Test Mode 74
- 1=DIAL, 0=WALK 75
- SECTION 14 77
- SECURITY CONTROL 77
- COMPATIBLE DEVICES 77
- System Sensor 78
- 5802CP Belt Clip (Personal 79
- Emergency) 79
- Same as 5802 79
- Regulatory Agency Statements 81
- UL NOTICES 82
- Limitations and Warranty 83
- (Continued) 84
- – INDEX – 85
- SUMMARY OF CONNECTIONS 87
- ADEMCO LIMITED WARRANTY 88
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15
(80 strony)
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji