ADEMCO Security System VISTA-15 Dokumentacja Pobierz pdf (Strona 33)

FIELD TITLE and DATA ENTRIES EXPLANATION

*86

Cancel Verify

0 = no

1 = yes

When enabled (1 = yes), this feature causes a “

CANCELED

ALARM

”

display on the LCD keypad under the following

conditions:

•

After the kissoff of the cancel message to the Central Station,

indicating a successful transmission.

•

When an alarm is successfully canceled before the Central

Station received the Alarm message. E.g., if an alarm is

incorrectly triggered and the user presses code + OFF before

the dial delay time has expired, the message will never go out

to the CS.

•

When the Cancel report is not enabled and the system is

disarmed:

before

dialer delay expires (alarm report not sent)

message “Canceled Alarm” is displayed.

after

dialer delay expires message “Canceled Alarm” is

not displayed

*87

Misc. Fault Delay Time

0 = 15 secs 6 = 2-1/2 min #+12 = 8 min

1 = 30 secs 7 = 3 min #+13 = 10 min

2 = 45 secs 8 = 4 min #+14 = 12 min

3 = 60 secs 9 = 5 min #+15 = 15 min

4 = 90 secs #+10 = 6 min

5 = 2 min #+11 = 7 min

Used with zones assigned to a configurable zone type with fault

delay on (configurable zone type digit “6”), and sets a zone

response time of 15 seconds to 15 min. It can be assigned to

zones with sensors that provide a trouble indication when an oil

tank is low, or similar applications for critical condition

monitoring where a non-alarm response is desired.

UL: May only be used on non-burglar alarm and non-fire alarm

zones when used on a fire and/or UL burglar alarm installation.

*88

Program Mode Lockout Options

0 = standard *98 installer code lockout

1 = lockout [

∗

] + [#] reentry after *98 exit (reentry

via installer code only)

2 = not used

3 = lockout all local programming after *98 exit

(reentry via downloader only)

Select the desired options. The following table summarizes the

Program mode lockout options:

Exit *88 Reentry By:

Command Entry Installer Power-up† Downloader

*99 n/a yes yes yes

*98 0 no yes yes

*98 1 yes no yes

*98 3 no no yes

† pressing [∗] + [#] within 50 seconds of power up

*89

Event Log Full Report Code

0 = no report

1-F = see description above *59

If an Event Logging selection is made in field ∗90, a message can be

sent to the central station receiver when the log is 80% full. If the log

becomes full, new messages overwrite the oldest messages in the log.

*90

Event Log Enables

0 = no event logging

1 = log Alarm/Alarm Restore

2 = log Trouble/Trouble Restore

4 = log Bypass/Bypass Restore

8 = log Open/Close

x = log combination of events (add value of

entries)

This system has the ability to record various events in a history log

(VISTA-20P = 100 events; VISTA-15P = 50 events). At any time, the

downloader operator can then upload the log and view or print out all

or selected categories of the log. The downloader operator can also

clear the log. Event log can also be viewed at an alpha keypad.

The display/printout at the central station will show the date, time,

event, and description of the occurrences.

Data Entry Example: To select Alarm/Alarm Restore” and

“Open/Close”, enter 9 (1+ 8); to select all events, enter #15.

*91

Option Selection

0 = none

4 = using Audio Alarm Verification (AAV) unit

8 = Enable Exit delay restart/reset ††

UL installations using the AAV

feature must use the ADEMCO UVCM

module (part of the ADEMCO UVS

system).

Exit Delay Restart/Reset must be disabled.

FOR SIA INSTALLATIONS:

Exit delay

should be enabled.

Multiple choice example: for both AAV and

Exit delay restart†, enter # + 12 (4 + 8).

Select the desired options by adding the values of each desired option.

†

†“Exit Delay Restart/reset” option allows use of the [∗] key to

restart the exit delay at any time when the system is armed STAY or

INSTANT. This feature also enables automatic exit delay reset,

which resets exit delay if the entry/exit door is re-opened before exit

delay time expires after arming AWAY.

IMPORTANT:

AAV should not be used when Paging or Alarm

Reports are sent to a secondary number unless the monitoring zone

option is used (which pauses calls). Otherwise, the call to the

secondary number by the communicator after the alarm report will

prevent the AAV from taking control of the telephone line, and the

AAV “Listen in” session cannot take place.

4-7

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 87 88

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Security System VISTA-15 Dokumentacja Strona 33

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Security System VISTA-15