ADEMCO LYNX Podręcznik Użytkownika Pobierz pdf (Strona 3)

System Programming

For advanced interactive mode programming refer to the end of the System Programming procedure.

Step Action

Enter Programming mode: Installer Code + 8 0 0.

2. Set a programming default as follows:

Press *97, then press a number 1-4 to select a default table. Refer to LYNXR-ENSIA Programming Default

Tables.

3. Program the variable data fields as follows:

a. RF House ID - Press *24, then enter the desired 2-digit RF House ID for wireless keypads.

b. PABX Access Code (if used) - Press *40, then enter up to 6 digits. If fewer than 6 digits are used, press [*]

to end the field and advance to the next field.

c. Primary Phone Number - Press *41, then enter the primary phone number, up to 20 digits. If fewer than 20

digits are used, press [*] to end the field and advance to the next field.

d. Secondary Phone Number (if used ) - Press *42, then enter the secondary phone number, up to 24 digits. If

fewer than 24 digits are used, press [*] to end the field and advance to the next field.

e. Primary Account Number (if used) - Press *43, then enter the secondary account number. If only 3 digits are

used, press [*] to end the field and advance to the next field.

f. Secondary Account Number (if used) - Press *44, then enter the secondary account number. If only 3 digits

are used, press [*] to end the field and advance to the next field.

g. Pager Characters - Press *88 if using Default Table 4, then enter up to 16 digits which may be required by

your pager service (e.g. account number, PIN, etc.). If fewer than 16 digits are used, press [*] to end the field

and advance to the next field.

Note: If you are using Default Table 2 you must select a Pager Report Format in Field *49.

h. Download Phone Number - Press *94, then enter the downloading computer phone number, up to 20

digits. If fewer than 20 digits are used, press [*] to end the field.

4. Enhanced Sequential Mode - Press *83, then follow the prompts as follows:

A 01 a. Zone Number - Enter 2-digit zone number of the first transmitter to have its serial number

entered. The system will announce the Voice Descriptor for the selected zone number, if it is

programmed.

Press [*] to continue. Starting with this zone, the system will search for the first transmitter,

which has all of the following attributes pre-programmed in Zone Programming.

1) The correct input type selected in *56 (RF, UR, or BR programmed)

2) The correct loop number selected in *56

3) No serial number programmed

4) Zone type

Notes: 1. If the first zone number entered does not have one or more of the above attributes, the system will

search its database for the first zone that does, and will display it at the ENROLL SERIAL NUMBER

prompt (1b).

2. Pressing 00 exits mode, upon which the prompt “83” blinks, indicating the mode is inactive.

b. Enroll Mode - If “L” is displayed, the serial number for this transmitter has already been entered,

however, it may still be confirmed, viewed or deleted.

1) If the transmitter’s serial number has not been previously entered, enter the enroll serial

number mode now by pressing “1”, or copy the last serial number that was entered by

pressing “2”.

2) If the transmitter’s serial number has been previously entered, it may be viewed by pressing

“3” or deleted by pressing “9”.

Note: If view is selected; each digit will be re-displayed, and the keypad will beep once for digits 1-6, and three times

for the last digit.

3) Once the serial number has been entered the system will return to the (1A) prompt and “L”

will be displayed.

Note: This point can be faulted and restored and the panel will listen for the transmission.

4) The serial number/loop number combination that was entered can be confirmed by faulting

and restoring the zone being entered. If the panel receives a transmission that matches the

serial number and loop number entered, the keypad will beep three times, and “C” will be

displayed. This indicates that the serial number transmission has been confirmed to match.

No further transmissions will be received.

Note: When confirming a 4-button key, it assumed that all loops are used and only the serial number is confirmed.

Pressing any key will allow a confirm. Two beeps indicate that the template has been accepted. A single long

beep indicates illegal entries, or duplicate serial number/loop entry.

- 3 -

1 2 3 4 5 6 7 8

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO LYNX Podręcznik Użytkownika Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO LYNX