ADEMCO VISTA-20HWse Instrukcja Naprawy Strona 28
- Strona / 84
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
–28–
Programming the 4285 Phone Module
The system must be programmed for use with the 4285 Phone Module, including
assigning a phone code and selecting words from the alpha vocabulary. Refer to
the Programming sections for specific programming details.
Checking the Operation of the 4285 Phone Module
To Check Phone Module Operation From an On-Premises Phone:
1. Pick up phone and enter the programmed 2-digit phone code. Annunciation of
a system status report should automatically start. See the User’s Guide
accompanying the Phone Module for detailed information regarding the nature
of the status report, if necessary.
2. During any pause in the status report, or immediately following it, key the
following via the keypad on the phone:
Installer Code (4112), then press key 1 (OFF).
3. A ”beep” should be heard on the phone and from a wired keypad, and the
words DISARMED...READY TO ARM or DISARMED...NOT READY TO
ARM * should be heard, indicating that the command was entered
successfully.
* DISARMED...NOT READY TO ARM would indicate an open zone.
4. Hang up the phone.
To Check Phone Module Operation From an Off-Premises Phone:
1. Have someone dial the premises phone number, using a TouchTone phone.
¥ If the phone system does not include an answering machine, 2 long tones
will be heard in the caller’s phone, followed by a voice prompt "HELLO,
ENTER PHONE CODE NOW". The caller should enter the programmed
2-digit phone code.
¥ If the premises phone system includes an answering machine, the 2-digit
phone code should be entered during a pause at the beginning of, or
during, the outgoing answering machine message.
2. When the 2-digit phone code is entered, the caller will hear a voice prompt
asking for entry of the 4-digit system code ("ENTER SYSTEM CODE
NOW").
3. The caller should then enter the installer code (4112). As a safety feature,
there is a 3-try limit in which to enter each code (phone code and system
code), after which time the call-in will be aborted. Also, if no keys are pressed
for a period of 20 seconds, the call-in will be aborted.
4. Annunciation of a system status report will start if both codes were entered
correctly.
5 During any pause in the status report, or immediately following it, the caller
should key the following via the keypad on the phone:
Installer Code (4112), then 1 (OFF).
6. A ”beep” should be heard (and from a wired keypad on the premises), and
the words DISARMED...READY TO ARM or DISARMED...NOT READY TO
ARM * should be heard on the caller’s phone, indicating that the command
was entered successfully.
* DISARMED...NOT READY TO ARM would indicate an open zone.
7. At this point, the caller can hang up the phone.
8. Verify with the caller that there was successful access to the system and that
the appropriate annunciations were heard over the phone.
9. If the Phone Module functioned satisfactorily, unplug the AC transformer from
the AC outlet.
- VISTA-20HWSE 1
- TABLE OF CONTENTS 3
- LIST OF FIGURES 5
- INSTALLING THE CONTROL 10
- TERMINALS 11
- ON CONTROL 11
- FINAL POWER UP 12
- POWER UP 13
- PARTITION 1 KEYPADS 14
- PARTITION 2 KEYPADS 14
- – + IN OUT 15
- AUX AUX. DATA DATA 15
- System Sensor 17
- 1 2 3 4 5 20
- ÊÊSection 6 22
- NO C NC 23
- 25
- Section 7. 4285 PHONE MODULE 25
- 4285 WIRING NOTES: 27
- CONTROL DATA IN 31
- CONTROL DATA OUT 31
- RADIO DATA OUT 31
- RADIO DATA IN 31
- Example: 34
- 25 WIRED ZONE EXPANSION 36
- 20 INSTALLER CODE 36
- 21 QUICK ARM ENABLE 36
- Typical prompt displayed 37
- Section 13 38
- No entry delay 39
- SYSTEM OPERATION 40
- (per armed period) 0 41
- 3 41
- Part. 1 Part. 2 41
- ZONE PROGRAMMING 48
- OUTPUT DEVICES 48
- ALPHA DESCRIPTION PROGRAMMING 48
- (*56 Menu Mode) 49
- 1 00 AW: 1 50
- Menu Mode) 51
- STOP (STP): 52
- 00 54
- Zone List Displays 55
- Section 18 56
- ALPHA DESCRIPTOR PROGRAMMING 56
- Summary Mode Display 57
- S ZN 01 BACK 58
- (Word Space) 60
- CONTROL (DOWNLOADING) 61
- AWAY (MAX) 65
- AWAY/MAX 65
- STAY/INSTANT, Quick Arm 65
- STAY/INSTANT 65
- Panic Keys 67
- SMOKE DETECTOR 71
- CONTACTING TECHNICAL SUPPORT 72
- REGULATORY AGENCY STATEMENTS 73
- Ð NOTES Ð 80
- SE SUMMARY OF CONNECTIONS 83
- N7526-2V2 8/97 84
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA-20HWse
(28 strony)Triton 97XX Configuration Manual podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Ekwipunek Triton 97XX Configuration Manual.
Dostarczamy 1 pdf podręczników Triton 97XX Configuration Manual do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji