ADEMCO VISTA-250FBP Instrukcja Konfiguracji Pobierz pdf (Strona 105)

10-1

SECTION 10

Testing the System

•••••••••••••••••••••••••••••••••••••••••••••••••

Battery Test

When AC power is present, the VISTA-128FBP/VISTA-

250FBP runs a brief battery test every 60 seconds to

determine if there is a battery connected, and runs an

extended battery test every 4 hours to check on the

battery’s condition.

If the VISTA-128FBP/VISTA-250FBP finds that the

battery voltage is low (less than approximately 11.5V),

it initiates a keypad “SYSTEM LOBAT” display and a

rapid keypad beeping sound. It also sends a Low

Battery report to the central station (if programmed).

The keypad is cleared by entering any security code +

OFF, and a Restore report is sent to the central station

if the situation has been corrected.

Dialer Test

The VISTA-128FBP/VISTA-250FBP may be

programmed to automatically transmit test reports to a

central station at intervals ranging from once per hour

to once per 9999 hours (field ✳27).

Commercial Fire Alarms and Commercial Burglary

requires the test report to be transmitted at least once

every 24 hours. The system can be programmed to send

the first report at any time of the day, or on any day of

the week (field ✳83).

Fire Drill Test (Code + [#] + 69)

This test causes fire Notification Appliance Circuits to

be activated for the purpose of conducting a fire drill or

bell test. This test can only be activated by the installer

or master users from partition 1 keypads by entering

the corresponding security code + [#] + 69. The burglary

portion of the system must be disarmed.

Keypads display “FIRE DRILL ACTIVE” while the test

is active. The test is stopped by entering any user code

+ OFF.

The system continues to monitor all 24-hour type zones

(fire, panic, etc.) and ends the test if any of these zone

types produce an alarm condition.

This test should be conducted at periodic intervals, as

determined by the local authority having jurisdiction.

One-Man Fire Walk-Test (Code + [#] + 68)

This test causes the system to sound console beeps and

Notification Appliance Circuit dings in response to fire

zone faults (zone type 9, 16 and 17) for the purpose of

allowing proper zone operation to be checked without

triggering alarms. Note that the system will not be

operational as an alarm system (i.e., cannot sense

alarms) while this test is active. The test can only be

activated by the installer by entering the Installer’s

Code and pressing [#] + 68 while the burglary portion of

the system is disarmed.

This test should be conducted at periodic intervals, as

determined by the local authority having jurisdiction.

When testing non-latchin

devices, such as heat

detectors, be sure to keep the device faulted

until the system responds with the keypad beep

or siren sound. If the device is faulted only

momentaril

, the s

stem ma

not respond to the

fault.

When this test is first activated, the system will display:

PROMPT

EXPLANATION

USE BELL DING?

0=NO 1=YES

Enter 1 (YES) to have the fire Notification Appliance Circuits associated with each point sound for 3 seconds

when a point is faulted.

Enter 0 (NO) if only keypad sounders are desired.

The next prompt will be displayed.

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 135 136

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO VISTA-250FBP Instrukcja Konfiguracji Strona 105

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA-250FBP