ADEMCO Accord Dokumentacja Pobierz pdf (Strona 16)

Figure 2.4 Connections to the Accord.

Testing the Installation

Power-up and Initial Test Procedure

When the Accord control panel has been installed in accordance with the preceding

safety and wiring instructions the system should be tested. The test procedure is

outlined below.

Note: Before the test commences all auxiliary devices such as powered sensors

(PIRs), remote keypads, alarm sounders, etc, must be connected.

The Standby battery should not be connected at this point.

Group 5  Option 4 Keypad Panic

When enabled (set to 1) this option gives a double-push panic button facility on the

keypad. Both the Ö and # buttons must be held down for two seconds to generate

the panic alarm. The panic condition is indicated by all zone LEDs on the keypad(s)

activating.

Panic Alarms are affected by system option 5.3.1 Engineer Reset for Alarms.

Group 5  Option 5 Keypad Lockout

When enabled (set to 1) this option locks-out the keypad if 20 keys are pressed

without a valid code being entered. This lockout lasts for 10 minutes. Keypad lock-

out is indicated by two illuminated zone LEDs on the keypad scrolling up and down

in opposite directions.

A keypad lockout may be cancelled by operating a zone programmed as keyswitch.

Group 5  Option 6 Bell Output

When set to 0 the Bell output is positive removed (negative applied)  set to 0 by

default.

When set to 1 the Bell output is positive applied (negative removed).

Group 5  Option 7 Trigger Output

When set to 0 the Trigger output defaults to positive removed (negative applied) 

set to 0 by default.

When set to 1 the Trigger output is positive applied (negative removed).

System Programming  Group 9 Factory

Defaults

The control panel programming can be reset to the factory defaults. This is done from

Programming Mode by pressing 981.

If the Engineer or Master User Codes have been lost they can be defaulted separately

from the rest of the system. This is done from Day Mode:

 Power down the control.

 Re-power the control.

 Hold down Ö and # keys together until two beeps are heard.

The Engineer Code is now 9090 and the Master Code is 1234.

Table 3.10 Group 9 System Options.

SNOITPOMETSYS

PUORGNOITPOTLUAFED

9.)seY=1,oN=0(stluafeDyrotcaFteS=8)0(

BELL

–

BELL

TAMP

–R

STRB

–

n/c

n/o

–

BELL

–

BELL

TAMP

–R

STRB

+ Supply/Hold-off

Trip/Signal Negative

– Supply/Hold-off

– Tamper return

Strobe – signal

BAT+

BAT–

GND

Primary

AC Mains transformer

Secondary

–

Stand-by Battery

Max 7.2 Ahr

Live

Earth

Neutral

To a.c. mains input

MAINS AND BATTERY CONNECTIONS

AUX

–

TRIG

K'PAD

FULL

SET

PART

SET

NIGHT

SET

TEST ISOLATE

CODE CHIME

ESCAPE LOG EASY SET

123

456

789

ZONES

TAMPER

DAY

POWER

kpad

+ve

–ve

F1 Battery: 1 A, 20 mm Anti-surge

F2 Keypad/Auxiliary: 500 mA, 20 mm Anti-surge

F3 Bell: 500 mA, 20 mm Anti-surge

Mains Fuse: 100 mA, 20 mm Anti-surge

FUSE RATINGS

CONNECTIONS FOR BELL AND STROBE

CONNECTIONS FOR SAB

KEYPAD AND

LOUDSPEAKER WIRING

ZONE

TAMP

ZONE

ZONE WIRING

Normaly closed (Open for zone activation)

1 2 ... 11 12 13 14 15 16 17 18 19 20

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO Accord Dokumentacja Strona 16

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Accord