ADEMCO Accord Instrukcja Instalacji Strona 5
- Strona / 78
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
V
Group 6 — Option 9 Central Station (ARC) Receiver Handshake......................................... 31
System Programming - Group #6 Confirm Options (DD243)........................................... 32
Group #6 - Option 1 Report Confirmed Alarms ..................................................................... 32
Group #6 - Option 2 Timeout Alarm Affect Confirm ............................................................... 32
Group #6 - Option 3 Walk Through Affects Confirm .............................................................. 33
Group #6 - Option 4 Full Reset for Unconfirmed Alarms ....................................................... 33
Group #6 - Option 5 Signal Locked out zones....................................................................... 33
Group #6 - Option 6 Entry Timer Clears Confirm Count ........................................................33
Group #6 - Option 7 Restart Confirm Time on Repeated Single Zone .................................. 34
Group #6 - Option 8 Disable Keypad Unsets......................................................................... 34
System Programming — Group 7 Comms Options 2 ...................................................... 35
Group 7 — Option 1 Dual Reporting ..................................................................................... 35
Group 7 — Option 2 Dial Type .............................................................................................. 36
Group 7 — Option 3 Prevent Full Set if Line Fail................................................................... 36
Group 7 — Option 4 Bell Delay ............................................................................................. 36
Group 7 — Option 5 Exit Terminate....................................................................................... 36
Group 7 — Option 6 When to Communicate .........................................................................37
Group 7 — Option 7 Line Fail................................................................................................ 37
Group 7 — Option 8 Downloader Options .............................................................................38
Group 7 — Option 9 Zone Auto Omit .................................................................................... 38
System Programming – Group 8 Communication Enable / Disable ............................... 39
Group 8 — Option 9 Communicate Periodic Test Report ...................................................... 40
System Programming — Group 9 Parameters.................................................................. 41
Group 9 — Option 1 Communicate Omitted Zones............................................................... 41
Group 9 — Option 2 Invert Open/Close Signals.................................................................... 41
Group 9 — Option 3 Double Knock Zone ..............................................................................41
Group 9 — Option 5 Restore Signals on Unset or Reset ...................................................... 42
Group 9 — Option 6 Entry Deviation Permitted..................................................................... 42
Group 9 — Option 7 Print Event Log..................................................................................... 43
Group 9 — Option 8 Factory Defaults ................................................................................... 43
Group 9 — Option 9 Show Software Version ........................................................................ 43
Group 0 Communications & RF ......................................................................................... 44
Group 0 — Option 1 Technistore Version .............................................................................. 44
Group 0 — Option 2 Confirmed Alarm Time Window ............................................................ 44
Group 0 — Option 3 Report Low Batt in Channel 9 or Contact ID......................................... 44
Group 0 — Option 4 RF Keyfob Set/Unset Options .............................................................. 44
Group 0 — Option 5 Transmitter Supervision Time Window ................................................45
Group 0 — Option 6 Audible Jam & Supervision Loss .......................................................... 45
Group 0 — Option 7 RF Low Battery Warning....................................................................... 45
Group 0 — Option 8 Prevent Setting with Jamming Signal Detected .................................... 45
Group 0 — Option 9 Report AC Fails in Channel 9, or Contact ID ........................................ 45
Zone Type Definitions......................................................................................................... 46
General Information............................................................................................................... 46
0 — Not Used........................................................................................................................ 46
- Installation Manual 1
- Contents 3
- Safety Compliance 9
- Mains Supply Connections 10
- Telecoms Approvals 11
- Zone Cable Type 12
- Equipment Electrical Rating 13
- Ancillaries Pack 15
- Initial Mounting 15
- SW1 — Accord Tamper 16
- To remove the PCB: 16
- To replace the PCB: 16
- Tip: Use 18
- ALARM TAMP 19
- XPC to the PSTN 20
- Final Mounting 22
- Testing the Installation 23
- Table 3.1 Programming Groups 26
- Part and Night Set) 27
- Table 3.4 Night Set Zones 28
- Programming System Options 30
- Table 3.7 Bell Cut-off Times 31
- 0. Set (on in any set state) 32
- Table 3.12 No of Rings 38
- 0 = Comms Disabled 39
- 1 = High Speed (8 channel) 39
- 2 = Contact I.D 39
- 1 Before Entry 40
- 2 Except Entry 40
- 3 Always 40
- 1 Always disable 42
- 2 Full set only 42
- 3 During Entry 42
- 0 Single Report 43
- 1 Dual Report 43
- Table 3.14 Group 8—Triggers 47
- Table 3.16 System Parameters 49
- Zone Type Definitions 54
- Instructions 57
- Wire Free Programming 58
- From programming mode: 59
- Site Surveying 61
- Walk Test 61
- Reprogramming Your Code 65
- Programming New User Codes 66
- Printing the Event Log 67
- What they Mean 69
- Appendix A: Specifications 71
- Physical Width: 120 mm 72
- Height: 120 mm 72
- Depth: 25 mm 72
- PROGRAMMING FORM 74
- IP1-1232 Issue 4 75
- Redditch, B98 9HE 76
- IE1-1232 Issue 3 78
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO Accord
(8 strony)
(56 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji