ADEMCO VISTA-15PSIA Dokumentacja Pobierz pdf (Strona 12)

– 12 –

∗

∗∗

∗89

Event Log Full Report Code

See box above field *59 for report code

entries.

[00]

If an Event Logging selection is made in field ∗90, a message can be

sent to the central station receiver when the log is 80% full. If the log

becomes full, new messages overwrite the oldest messages in the log.

∗

∗∗

∗90

Event Log Enables

0 = None

1 = Alarm/Alarm Restore

2 = Trouble/Trouble Restore

4 = Bypass/Bypass Restore

8 = Open/Close.

Example: To select “Alarm/Alarm

Restore”, and “Open/Close”, enter 9 (1

+ 8)

To select all, enter #15.

[3]

This system can record various events in a history log (VISTA-20P =

100 events; VISTA-15P = 50 events). At any time, the downloader

operator can then upload the log and view or print out all or selected

categories of the log, or can clear the log. Event log can also be viewed

at an alpha keypad. The display/printout at the central station will show

the date, time, event, and description of the occurrences.

Data Entry Example: To select Alarm/Alarm Restore” and

“Open/Close”, enter 9 (1+ 8); to select all events, enter #15.

NOTE: System messages are logged when any non-zero entry is made.

∗

∗∗

∗91

Option Selection / Remote

Interactive Services (RIS) Enable

Entry 1: Options

0 = None

1 = Bell Supervision Processing

4 = AAV

8 = Exit Delay Restart/Reset†

#+12 = AAV and Exit Delay

Restart/Reset

Entry 2: Remote Interactive Services

(RIS) enable

0 = RIS disabled

1 = not applicable

2 = RIS enabled

V20PSIA/V15PSIA:

Entry 1 Options: Same as above.

Entry 2 Call Waiting Disable / RIS

Enable:

0 = call waiting not used

1 = use call waiting disable digits

(∗70) entered in field ∗40; (when

selected, the system dials the

entry in ∗40 only on alternate dial

attempts; this allows proper

dialing in case call waiting

service is later canceled by the

user).

2 = RIS (Remote Interactive

Services) enabled

3 = Call Waiting disable and RIS

enabled

[8, 0]

Options RIS Enable

V20PSIA/V15PSIA: Call Waiting Disable / RIS Enable

IMPORTANT: AAV should not be used when Paging or Alarm Reports

are sent to a secondary number unless the monitoring zone option is

used (which pauses calls). Otherwise, the call to the secondary number

by the communicator after the alarm report will prevent the AAV from

taking control of the telephone line, and the AAV “Listen in” session

cannot take place.

UL: for AAV, must use Honeywell AVS system; Exit Delay

Restart/Reset must be disabled

SIA Guidelines: Exit Delay Restart/Reset should be enabled.

† “Exit Delay Restart/Reset” option allows use of the [∗] key to restart

the exit delay at any time when the system is armed STAY or

INSTANT. This feature also enables automatic exit delay reset, which

resets exit delay if the entry/exit door is re-opened and closed before

exit delay time expires after arming AWAY. Automatic Exit Delay Reset

occurs only once during an armed AWAY period.

Remote Interactive Services (RIS) Enable: This option enables

enhanced Remote Interactive Services (RIS) such as Total Connect

2.0, Tuxedo/Z-Wave scenes and Home Automation (Control 4,

4232CBM), if supported by the communication service in use. If

enabled, device address 25 is automatically assigned.

To Enable Remote Services:

1. Enable the RIS option in this programming field (entry 2).

2. Use field ∗189 to enable a remote services emulated keypad

address.

3. Use ∗29 Menu mode to enable the communication device.

4. If using Total Connect 2.0, use AlarmNet Direct website to program

the communicator and enable TC2 services. Be sure to “send” the

programming data down to the Communicator.

∗

∗∗

∗92

Phone Line Monitor Enable

Entry 1::

0 = disabled, 1-15 = 1 min - 15 min

(#+10 = 10 min; #+11 = 11 min;

#+12 = 12 min; #+13 = 13 min;

#+14 = 14 min; #+15 = 15 min)

Entry 2:

0 = Keypad display when line is faulted

1 = Keypad display plus keypad trouble

sound. Each partition turns off its

own trouble sound. No automatic

timeout.

2 = Same as “1”, plus programmed

output device STARTS. If either

partition is armed, external sounder

activates also. External sounder

will be turned off by normal bell

timeout, or by security code plus

OFF from either partition (it need

not be the one that was armed).

[0,0]

1 2

Entry 1: Sets the length of time a phone line fault must remain after

detected before the second digit option is activated.

Entry 2: Selects the desired phone line fault response.

Option 2 may be used even if a relay unit or Powerline carrier device is

not connected to the control.

Programmed Output Device must either be programmed to be

STOPPED in field ∗80 or STOPPED by entry of [security code] + [#] + 8

+ device number. Partition in ∗80 should be set to “0,” for STOP.

UL: Field *92 must be enabled for fire alarm installations, UL commercial

burglar alarm installations and UL residential burglar alarm installations.

If the control unit is used on a UL commercial burglar alarm system which

requires 2 methods of remote communication, then the control unit’s DACT

and the other method of signal transmission must monitor each other against

communication failure and line fault. The fault must be received and

annunciated within 200 seconds of its occurrence.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 47 48

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO VISTA-15PSIA Dokumentacja Strona 12

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO VISTA-15PSIA