ADEMCO 4140XMP Dokumentacja Pobierz pdf (Strona 16)

POWERING THE SYSTEM

PRIMARY POWER

Pwer to the 4140XMP somml panel is supplied by mtial No,

1361. Plug-in Transformer which k mted at 16.5VAC, 40vA.

Catilon must be taken when wiring this t,a”sfOrmer to the

panel to guard against blwing the fuse inside the

transformer.

“ NO=. U5e 1S61ON Trmdormer in Cmatim instilstbns.

b not u= the 1361 CN

in UL Lsted ~~itbns.

BACK-UP POWER

In the event of an AC power IOS, the 4140XMP ~mmI pa”eI

is supponed by a b~k-up, r~hargeable gel cell batte~.

YUASANP&l2(12V, 4AH) andNP7-12(12V, 7AH) bstterias

are recommended. Do not u- Gatae batterlas

(sealed Iced-acid type).

The standby baftey is auto”mathlly tested eve~ 24 houm,

baginning24 hours after exiting programming mode. In

addition, ent~intothetast mde will =useabatte~ teat to

be initiated.

BA~ERY BTANDBY TABLE

4140XMP AUX. STANDBY CURRENT DRAW

,AMP-HRs. 1200mA I 400mA

I 600mA I 750mA

4.0.

I 6hrs.

[ 4 hrs.

I 3 hrs. [ 2.5 hm.

7.0

Illhm.

I 7 hrs,

I 5.S hrs.

14 hrs.

NOTE: The~vefigures areapproximata, ati mayvay

de~nding upon the age, qua~iy, and cqictiy of the battefy

at the lima & the AC loss.

. Uss 4AH b~aW for UL installations.

POLLING LOOP CURRENT DRAW WORKSHEET

RPM DEVICE

CURRENT # UNITS [ TOTAL

I CUR ENT

4194 Conkd

lti

4192S0 Phob SmWe

0.4MA

4192SOT&& WHeat

0,4d

4192GP 10”SmO@

0.4d

4275 O“al PIR

lti

4278 Quad PIR

lti

41S02-Z- RPM

1MA (LOW)

2 MA (HIGH)

4208 S-20M RPM

1sd

42S0~ 20”e RF

4oti

4zw S20W RF

4oti

JTOTAL ..

.. If ti M*I cuwnt &w ex~ds 64 mA, a 4197 ~

Exm*r mtiule must be usd,

.. If utiw MO 42WS or 42-s, you -n -r m of M

km a.xil~ p- inswad of .al”g a4187 mp e~~m

&b.

EARTH GROUND CONNECmONS

In ordar for tha tightning transient protetiiva davices in this

product to be aflatiiva, the designated eanh ground

terminal, must bs tarminatad in a god aadh ground. The ~

following ara examples of gmd aafih grounds availabla at

most installations:

Metal Qld Water Pipe: Use a non~rrosive metal strap

ti~ly sasured to tha pips to which tha

ground laad iS

alastri~lly rnnnadad and seargd.

AC Powar Outlat Ground: Availabla from 3-prong,

120VAC, pwar owlats only. To test the intagiiy of tha

ground tarminal, usa a threa-wire circuit taster whh neon

lamp inti=tom, such as the UL-List~ Meal Modal 61-035,

or equivalent, avaibble at most eladrtii supply storas,

POWER-UP PROCEDURE

1. Fill OM tha PolUng Lmp Currem Draw ad Auxifia~ Deviw

Currem Draw Workshaats shown bebw. Maka sura that

tha currants drawn from these otiptis do not exceed

their respa~ive ratings.

CAUTION: Failura to obsewa tha ~iiing loop currant

rating will cause polling loop malfuntiion. Failure to

obseme the auxifla~ outpffl cumanl rating will result in a

battery which doss not charge proparly or posaibiy a

trippd circuti breakar.

2. ~re the 1361 transformer (1361 CN in Canada) tO the

panal (bafora mnnecting tha batte~) as shown in the

SUMMARY OF CONNECnONS diqrm. b nd plug in at

this time.

2. Connsot all polfing loop and auxilia~ devias, such as

rnnsolas, PIRs, etc.

3. Plug the 13St into an 24 hour, unitiemupted AC otilet. In

a faw semnds, tha graan POWER LED on the rnnsoie(s)

ahouw I@ht and tha mnsola(s) ahouM display .READY.

(4127. 4137) or “DISARMED READY TO ARM” (513~,

4. bnnist the batte~ as shown in the SUMMARY OF

~NECTIONS disgrm.

AUXILIARY DEVICE CURRENT DRAW WORKSHEET

OEVICE

I CURRENT j # UNITS I TOTAL

a, ,”-----

*“””en,

14127@S~

Imti

14137GS*

Iso@

I TOTAL

(7~ti max)

. II using bti-w,re dev,~s such as PIRs, retw to ti spcifi~tions

~r Bat pticuhr univs w-t draw.

t Only qd~s if wati * tiws autil~ pwer.

-16-

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 51 52

Komentarze do niniejszej Instrukcji

Brak uwag

ADEMCO 4140XMP Dokumentacja Strona 16

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa ADEMCO 4140XMP